Insulation for heating pipes: overview of types + application examples

Hello friends!
Water supply in an apartment building, private house or country cottage is a common occurrence; water should be available at any time of the year. However, temperature fluctuations can make significant adjustments to the water supply process. Apartment owners think little about how the water supply is organized, and owners of private houses are forced to take steps on their own to ensure that the water in the pipes does not freeze in winter.

At the same time, we note that frost does not spare either steel or plastic pipes. The only way to keep water in liquid form and prevent damage to the water supply system is to fully insulate the water pipes. After all, unlike a heating pipe system, there is no warm medium.

Due to the fact that thermal insulation is carried out on your own site, we are not talking about an industrial scale of work, which means it makes sense to study how to insulate water pipes with your own hands.

Methods for insulating water pipes outdoors (in the ground)

1. increasing pressure in the water supply system;
2. cable for heating a water pipe;
3. thermal insulation for water supply pipes.

1. Creating high pressure in the water supply system

The water pipe will not freeze because the water will move at high speed. To implement this method, a pump is used to increase the pressure in the water supply system or a receiver that cuts into the pipe directly next to the pump.

Heating cable for water supply

Cable power 10-15 W (average price – 15 USD/m.p.).
Excellent for heating pipes in the ground when they are placed at a shallow depth. According to the rules, it is not advisable to place any communications in the soil below the soil freezing level. There are situations in which this requirement is ignored. In this case, simple insulation of pipes will not give the desired result, because... the pipeline will in fact be located in water (in a humid environment that freezes in winter). Most of the insulation materials are not suitable for this mode of operation and do not provide proper thermal insulation.

Using a cable to heat the water supply makes it possible to lay pipes at a depth of up to 500 mm.

Heating cable for water pipe

The heating cable for insulating water pipes is wound along the pipe or around it with a given pitch. The pitch is determined by the power of the cable. The lower the power, the smaller the step. Methods for laying the heating cable are shown in the diagram.

Wiring diagram for installing a cable for heating a water pipe

Craftsmen and users note that insulating a water supply system by heating the pipe with a cable is the most reliable method for protecting pipes laid in the ground freezing zone.

Cable heating makes it possible to avoid freezing of water in the pipe, and, equally important, to quickly defrost frozen pipes. Such a need may arise at a dacha if it is intended for seasonal living. In this case, you can quickly prepare the pipeline for operation, because under natural conditions you can wait until May for complete defrosting (when laying pipes at the level of soil freezing). The cable is located both inside and outside the water supply pipe.

Application of thermal insulation materials for pipes

This is the most cost-effective and easiest insulation method from the point of view of independent implementation. Let's look at it in more detail. Let's start with the best way to insulate a water supply system, what materials can be better used depending on specific conditions.

Price

It's no surprise that king-size beds cost more than queen-size beds. Other than this obvious cost difference, however, there is no real average price for a bed of any size. Prices tend to vary depending on manufacturers, distributors, mattress material (e.g. spring, memory foam, latex, etc.) and pads (e.g. Eurotop or pillowtop). Personal finance blog Get Rich Slowly provides a guide to smart, affordable mattress shopping.

It can be difficult to figure out whether a king-size bed is worth the higher initial cost. Factoring in related and future costs can paint a clearer picture. For example, the bed frame, box spring, and linens for a king-size mattress will cost more than for a queen-size mattress.

Thermal insulation for water supply pipes

It is not difficult to get confused in the wide range of thermal insulation materials. To choose the best option, you need, at a minimum, to know the main types and types, key characteristics and features.

Thermal insulation of water pipes is carried out with various insulation materials, which are grouped below (in the form of a classification) according to the principle of unity of insulation technology.

Materials for insulating water pipes

Types, types, varieties and rules for choosing pipe insulation.

Rigid insulation

This category includes polystyrene foam, polystyrene foam (2560-3200 rubles/cube) and Penoplex (3500-5000 rubles/cube), thermal insulation properties and price depend on density.

Polystyrene foam is an excellent insulator and has a relatively low cost (compared to other materials). However, it is quite difficult to insulate a round pipe with a rigid insulation board. To insulate pipes, special shells (hard boxes) are used - shells in which pipes are placed, and the space is filled with soft insulation.

Laying water pipes in a foam box

Roll insulation

This segment includes: polyethylene (as an additional material), foil penofol (50-56 rubles/sq.m.), mineral wool (70-75 rubles/sq.m.) and glass wool (110-125 rubles/sq.m.) ), furniture foam rubber (250-850 rubles/sq.m. depending on thickness).

Insulating water supply pipes with rolled thermal insulation is also fraught with difficulties, which lie in the hygroscopicity of the material. Those. insulation loses its properties when exposed to moisture, which means it has a narrower scope of application, or needs additional protection. Plus, you need to think about how to attach the insulation to the pipe.

Basalt heat-insulating mats and foam rubber for insulation of water pipes

Segmental (shell) insulation

Pipe insulation casing is the most progressive option for pipeline thermal insulation. The shell for insulating the water pipe ensures maximum tightness and, as a result, creates a reliable thermal insulation layer.

There are types of segmental insulation:

Polystyrene foam shells for insulating water pipes are rigid (thermal insulating casing for pipes is a shell made of polystyrene foam (PPU) or foam plastic. Price from 190 rubles/m.p., depends on the thickness and diameter of the cylinder);

Sprayed insulation (PPU)

The peculiarity of insulation by spraying polyurethane foam is that thermal insulation is applied to the surface of the pipe, ensuring 100% tightness (the cost of components for polyurethane foam filling starts from 3.5 euros per kg).

The number of components is determined by the thickness of the fill; work is paid additionally). On average, the cost of insulation with sprayed polyurethane foam is 15-20 dollars/m.p.

Sprayed insulation also includes heat-insulating paint for pipes. You can apply it yourself, because... Thermal paint is sold in aerosol cans.

A layer of paint of 20 mm. replaces 50 mm of basalt wool insulation. In addition, this is the only material that is not susceptible to damage from rodents.

Insulation of water pipes by spraying polyurethane foam (PPU) Water pipe insulated with polyurethane foam (PPU)

When choosing thermal insulation material for insulating water supply pipes, you need to take into account the following factors:

• pipeline installation location. Insulation of pipes laid on the ground and located underground is carried out in different ways, even when using the same materials (it is also important to take into account whether the pipes are laid before or below the freezing level);
• frequency of pipeline operation. For example, in a country house that is not intended for permanent residence, it is enough to simply avoid a pipe rupture. To do this, a receiver is installed or the water supply is insulated with a cable. But in a private house it is necessary to ensure a year-round water supply. Here you need to approach the choice of insulation more carefully;
• thermal conductivity indicator of pipes (plastic, metal);
• resistance to moisture, combustion, biological activity, ultraviolet radiation, etc. determines the need to protect the insulation from these factors;
• ease of installation;
• price;
• life time.

How to properly insulate

Thermal insulation of heating pipelines in a private home is not very difficult; it can be done with your own hands. It is enough just to follow simple conditions. All the details of the pipe insulation process can be seen in the video.

On the street

When installing thermal insulation in an open space, it is important to ensure that the pipeline is reliably sealed from precipitation and to isolate the insulation from sunlight. Previously, mineral wool was often used for thermal insulation and wrapped in roofing felt; now shells made of PPS or polyurethane foam with an outer layer of galvanized steel, reinforced foil, fiberglass or fiberglass are usually used. The heating main on the street experiences constant wind loads, so it is necessary to select a durable material for thermal insulation - polyurethane foam, extruded polystyrene foam. For large-diameter heating mains, galvanized steel shells are used.

Underground

When installing thermal insulation underground, it is necessary to especially carefully seal the insulation of steel heating pipes. It is necessary to carefully glue the joints of the shells and seal difficult areas with polyurethane foam foam. The quality of installation of the heating pipeline and thermal insulation depends on the preparation of the trench - the slope must be maintained, the pipeline with thermal insulation must be covered with sand. Underground, it is best to use ready-made shells with an outer shell made of fiberglass, fiberglass, or kraft paper for thermal insulation.

Indoors

Inside dry rooms, attics, and basements, mineral wool is often used for thermal insulation of heating pipes - rolled or in the form of shells. On top it is wrapped in penofol, fiberglass, roofing felt, and fixed with wire or tape. You can also use foam shells or penofol.

How to insulate a water pipe with your own hands

The location of the pipes is another important factor that must be taken into account when choosing insulation. Indeed, depending on where the pipes are located (in the ground, basement, cold attic, unheated room), the temperature and humidity conditions are determined, as well as the ease of installation of the insulation and the need for its additional protection.

Insulation of water pipes on the street

Water pipes are rarely laid by air or on the soil surface. Rather, in this case, the part of the pipeline that runs directly under the house or at the junction of the pipe with the pump, meter, or inside the distribution well needs insulation.

The specificity of insulation in this case is such that the pipe is insulated with any insulation that is capable of ensuring a sufficient tightness of the fit and is not exposed to moisture.

As a rule, the thickness of the insulation intended for above-ground insulation of pipes is higher than for underground insulation. At this stage, it is important not only to insulate the pipe, but also to ensure protection of the thermal insulation material, in particular from getting wet.

Insulation of water pipes in the ground

Such insulation will be needed only if the pipes are laid above the soil freezing level. To insulate a pipeline in the ground, you can use any material, including rigid insulation.

It is worth noting that the insulation of external water supply does not end with the installation of insulation. It is important to protect the insulation from getting wet. To do this, a film, roofing material is wound over the main thermal insulation material, or a plastic box is installed.

Types of lathing

Let's move on to installation and start with choosing the sheathing. The sheathing is made from:

• wooden beams;
• profiles for fastening drywall;
• metal U-shaped profiles for siding;
• plastic structures designed for the installation of vinyl and acrylic panels.

Before installing the sheathing, inspect the surface. If there are cracks, crevices and other defects on it, they need to be repaired. If the old cladding is crumbling (for example, paint or plaster), it must be removed. If there are strong differences and unevenness on the walls, they should be smoothed out. Otherwise, the geometry of the wall will be disrupted and the siding may crack or deform.

After eliminating the unevenness, you need to treat the walls with a protective coating. To protect the walls of a wooden house, use an antiseptic and a fire retardant: the first will cope with moisture and rot, the second will prevent fire. Treat concrete walls with a deep penetration primer. It will prevent the appearance of mold and mildew.

Wooden sheathing for siding (photo No. 5)

The sheathing is mounted perpendicular to the siding panels. In other words, if you want to lay the siding horizontally, then the sheathing frame must be made vertical. And vice versa. The step between wooden beams or metal profiles should be 30-50 cm.

Hydro-wind insulation is laid under the sheathing. It protects the building from wind and moisture. Thanks to the presence of the lathing, a ventilation gap is formed between the walls of the house and the finishing panels. The gap prevents the appearance of condensation harmful to the walls and cladding. To keep the house warm, you can lay insulation between the sheathing. For this purpose, mineral wool and expanded polystyrene foam are used.

Let's take a closer look at each lathing option.

Wooden sheathing. It is made from beams 4 cm or 5 cm thick

When choosing beams, pay attention to the smoothness of the surface and the absence of cracks. Before installation, you need to dry the wood and cover it with solutions that protect the wood from rot and fire.

If you are faced with the question of how to attach siding to wood, then there are 2 options: with a screwdriver and self-tapping screws or with a hammer and nails.

Metal sheathing of walls and plinth (photo No. 6)

Profile for fastening drywall. If the goal is to save money, then profiles for interior work are used to install siding. Most often, sheets of plasterboard are attached to such structures. Manufacturers do not recommend using drywall profiles outdoors. Due to the thin zinc coating, corrosion occurs on them when exposed to moisture. They are intended for indoor use and are not suitable for attaching siding.

Metal U-shaped profile. To attach the siding, a durable metal profile 1 mm thick is also used. This design is more reliable than lathing with a plasterboard profile, but will be more expensive. If you use heavy cladding panels (for example, basement or metal siding), then you need to use street profiles.

Alta-Profile polymer façade fastening system. Polymer profiles are not subject to rust and rotting; they do not require additional processing or special storage conditions. If you choose vinyl siding to clad your building, you need to take into account that it expands in the hot summer and contracts in winter. Polymer profiles prevent deformation of cladding panels due to sudden temperature changes; they have the same coefficient of expansion as siding.

Plastic profiles are not subject to rust and rot (photo No. 7)

How to install a heating cable for heating pipes

For installation, prepare: foil tape, thermal insulation material, heating cable (power 20 W per linear meter).

Installing a heating cable on top and inside a water pipe

Technology for insulating water pipes with cable:

• the pipe along its entire length (from the well/well to the house) is glued with foil tape;
• The heating cable is laid in a convenient way with the same pitch. For a 20 W cable, a pitch of 100-150 mm will be optimal. For a less powerful cable, the pitch is reduced. The most convenient way to lay the cable is to wrap the pipe in a spiral;
• the cable is fixed with foil tape;
• Insulation is installed on the pipe. Pipes made of foamed polymers, basalt cylinders or polyurethane foam shells are placed on the pipe. In this case, it is necessary to ensure that the diameter of the pipe corresponds to the internal diameter of the segmental insulation. Before starting work, roll insulation is cut into strips, which are wrapped around the pipe and secured with clamps or wire. Their task is to hold the insulation in a given position.
• the insulation is fixed to the pipe with tape (plumbing tape). The tape is wrapped very tightly. The main task of the winding is waterproofing, i.e. prevent groundwater from entering the insulation;
• additionally insulate the pipe at the point where it reaches the soil surface. The following options are offered: additional winding with insulation or arrangement of a box in which the insulation will be placed.

Installation of cable for heating pipes

Regardless of the insulation method, it makes sense to choose only high-quality materials and install them according to the instructions. Of course, this affects the budget of the event, but expenses of this kind pay off in the future. And a frosty winter will not bring unpleasant surprises in the form of a lack of water due to freezing in pipes or a rupture in the water supply system.

Source: moydomik.ne

Selection rules

In areas where climatic conditions range from high to low temperatures, it is necessary to use insulation for heating and water pipes.

The materials used must meet the following requirements:

• thermal conductivity indicators should be minimal;
• resistance to chemical, biological, mechanical influences;
• non-flammability;
• safety for people and the environment;
• the melting temperature value must be higher than the coolant temperature;
• long period of operation;
• ease of installation;
• excellent sealing qualities;
• acceptable price.

The wide range of insulating materials for heating channels on the market allows you to make a choice based on the needs and desires of a person.

Pipe insulation is selected taking into account the following rules:

• the cross-section of the pipe is taken into account;
• the operating conditions of the heating system of the room are analyzed;
• the temperature of the coolant used is taken into account.

Insulation for pipes of different diameters is selected in relation to installation. For a pipeline with a small diameter, it is worth choosing cylindrical or semi-cylindrical materials that will be put on it. For pipes with a large cross-section, the use of heat-insulating materials is provided, which are produced in large packages in the form of rolls.

Tubular insulation material is produced in a rigid shape or soft, free-form insulation is possible.

Please note: rigid insulation helps prevent mechanical damage due to its dense structure.

Insulation materials

It is difficult to imagine comfortable living in a house without a constant water supply. However, many owners of their own houses and cottages face freezing water pipes in winter.

Frost does not spare either high-quality galvanized steel pipes or metal-plastic products from the best manufacturers, tearing all pipes equally harshly. You can avoid such a sad outcome if you promptly insulate the water pipes yourself.

The need to insulate the water supply

So, you understand the need to insulate the water supply in your home. Considering that there are not kilometers of pipes on the site, industrial-scale work will not be needed. Remember that the depth of the pipes should be up to half a meter.

Of course, the higher this indicator, the lower the risks that you will be left without water in winter. But even if you met this parameter when installing the water supply system, it is best to insulate it additionally.

Particular attention should be paid to the procedure for insulating water pipes in unheated rooms and outdoors, since these places are the most vulnerable to freezing.

If it is not so difficult to insulate the water supply inside the building, then the thermal insulation of pipes that are located on the street, especially in places where they come into contact with pumps, meters, as well as in distribution wells, will take more time and effort.

Materials for insulating water supply pipes

The time has long passed when water supply insulation was carried out using sweatshirts, cotton blankets and other improvised materials. Today there are many thermal insulation materials on sale.

That is why it is so important to be able to choose the right insulation and know what to pay attention to first. It is recommended to purchase material for pipe insulation based on its basic characteristics and ease of installation.

When choosing insulation, remember that it must meet the following requirements:

• have a low level of thermal conductivity and have good heat-saving properties;
• be durable and resistant to chemical and biological influences of environmental factors;
• have a minimum coefficient of water absorption (high water-repellent properties), since moisturizing the material significantly increases its thermal conductivity;
• work at high temperatures without losing its structure and its own physical properties.

Knowing the basic properties of insulation and the location of water pipes on a plot of land, you will be able to make the optimal choice of thermal insulator for insulating water pipes. It is mainly recommended to install them to insulate indoor water supply systems.

Let's look at what insulation materials are intended for insulating a water pipe:

1. Glass wool. Fiberglass insulation is used primarily for insulating metal-plastic pipes. Popular brands include Ursa, Knauf and Isover fiberglass insulation. Glass wool is characterized by low density; when using this material for thermal insulation of pipes, it is recommended to install additional external insulators such as roofing felt or fiberglass. And this already promises you additional time and material costs.
2. Basalt insulation. Insulation of this type is made in the form of cylinders, which makes it easy to install. For additional protection, the fiber is covered with a layer of roofing material, foil insulation or glassine. Despite the obvious advantages, the cost of such insulation is not very affordable.
3. Expanded polystyrene. This insulation is the most popular material for self-insulating water pipes. Expanded polystyrene insulating shells are available with or without an outer covering. This heat-insulating material is designed for reusable use for insulating water pipes outdoors and indoors.
4. Thermal insulation paint. This is a pasty mass of gray or white color, which is an innovative product in the domestic construction market. This composition is made on the basis of varnish or water with the addition of acrylic dispersion and fillers. It is best to apply heat-insulating paint using a sprayer. The thicker the paint layer you make, the higher the thermal insulation of the pipe will be. The paint can withstand high and low temperatures and has anti-corrosion properties. By the way, one layer of paint can replace polystyrene foam or glass wool.

Methods for insulating underground water pipes

Above we looked at the materials that are used to insulate pipes outside and inside the premises.
Some of the thermal insulators can be used underground. However, insulation in this way is not always easy and has many disadvantages. And therefore, it is worth paying attention to alternative methods of insulating water pipes in the ground when there is no need to lay pipes at a significant depth.

Let's take a brief look at these methods and find out how to properly insulate water pipes using them:

• Heating cable. Insulation occurs by heating the pipeline using a cable, the power of which is on average 10-20 W per linear meter, inside and outside the pipe. Since the winter season lasts only a few months, the insulation process is necessary exclusively during this time: the heating cable will only be turned on during such months. When using insulation, pipes do not need to be laid to a depth of 2 meters; it is enough to go only 50 centimeters deep.
• Insulation of pipes with air. In this case, you can use the materials listed above - polystyrene foam and basalt materials. The essence of the method is to insulate the pipes with air that comes from below, and to create a so-called “umbrella” from the cold air that comes from above. The pipe is placed in a cylindrical insulating material. The result is something like a “pipe within a pipe.”
• Insulation of water pipes using high pressure. As part of this technique, a receiver is inserted into the water supply system, where pressure is pumped into. This method will work best on submersible pumps, because they have the pressure necessary for the system (close to 5 atmospheres). But in order for the entire system to be under pressure, a check valve is installed immediately after the pump.

Other ways to prevent freezing

Another method that is successfully used in areas where the winter temperature drops below zero to critical values. It is called the umbrella or air gap method. Its essence lies in the operation of physical laws. The temperature underground will always be higher than outside in winter. In order to use this useful property, a larger diameter pipe is first laid, which will serve as a sleeve. The one that will serve as a highway is placed in it. The trench is filled with soil. The layer that remains between the two pipes will compensate for the temperature difference and prevent freezing.

Pipe in pipe

High blood pressure can also help in such a situation. The usual pressure value for a household network is 2 atmospheres. Water stops freezing at 4 atmospheres. On a section of pipe that will be located at negative temperatures, it is necessary to ensure this level. To do this, a special storage device and a supercharger are installed on one of its parts. A gearbox is mounted at the other end, which will prevent damage to household appliances.

Insulating the water supply with your own hands

All insulation materials that are used today for heating water pipes have exactly the same operating principle. The choice of specific thermal insulation will depend on the location of your plumbing and the water-repellent properties of the material.

Use of thermal insulation materials

Fiberglass is used to wrap the pipes, and then secure the wrapping with plastic tape. Next, it’s worth installing waterproofing - using roofing felt or other similar materials.

However, it is not recommended to insulate pipes located underground with fiberglass materials. Firstly, with this insulation method you will have to install two layers: the insulation itself and the casing, which consists of winding this heat insulator with some kind of waterproofing material. And this is quite long and tedious, which leads to an increase in the cost of insulating the water supply system.

Since the density of such heat-insulating materials is low, the thickness of the insulation when backfilling the trench will be disrupted in height, that is, the material will simply shrink under the weight of the soil, and this process can even continue for more than one season. As a result, the thickness of the insulation will not be enough to create high-quality insulation of the underground water supply.

If you backfill pipes using layer-by-layer compaction, this will only speed up the process. If the depth of the water supply system is insufficient, after prolonged autumn rains, surface water will most likely reach the heat insulator through loose soil (after backfilling), and it is unlikely to have time to dry out by winter.

Thermal insulation shells, made of basalt fiber or expanded polystyrene, are installed quickly and easily. Polystyrene foam halves of a certain diameter are placed on the water pipe with an offset of 100 - 200 millimeters relative to each other, first secured with tape.

An offset relative to each other is required for “overlapping”, which reaches 10 - 20 centimeters. To insulate corners, nodes and turns of the system, it is customary to use shaped shells.

The advantages of this method of insulating polystyrene foam water supply pipes are that the water absorption rate in 24 hours reaches only 0.5 - 2.0% by volume, so the insulation does not get wet and does not collapse under the influence of moisture, like glass wool.

When backfilling a trench, polystyrene foam will not wrinkle or get wet when surface water penetrates the soil. The same insulation technique can also be used when passing a water supply through an unheated room.

Application of heating cable

Let's consider organizing heating of the water supply using a special cable. I would like to immediately make a reservation that this is not a cheap pleasure, although if you install the pipes yourself, you can save a lot.

There are two types of cable heating of water pipes. In the first case, the wire runs inside the pipe, but the installation procedure is quite complicated, and it will be very difficult for a non-specialist to cope with it.

In the second case, the wire passes over the pipe, but the power and its length are calculated before installing the heat-insulating material. It is much easier to install it yourself.

By the way, there are ready-made kits for sale for arranging a water supply system, consisting of a pipe with a built-in heating cable and thermal insulation material, or without a wire, but with a cable channel made for it.

If you use this method of heating pipes, then you do not have to bury the water supply 2 - 2.5 meters, 50 centimeters is enough. To do this, you will need the following materials: plumbing and foil tape, waterproof insulation, self-regulating cable for insulating water pipes, which has a power of at least 20 W per meter. In addition, the heating cable allows not only the pipes not to freeze, but also to quickly defrost them.

The process of insulating a water pipeline with a heating cable occurs in the following sequence:

1. Along the pipe that runs to the house from the well, you need to glue foil tape in a spiral. It is not glued too tightly so that the wire holds when winding through the pipe.
2. After this, it is necessary to lay the heating cable along a pre-prepared spiral in increments of 10 - 15 centimeters.
3. You should also stick foil tape over the cable, which will secure the wire.
4. The insulation needs to be cut lengthwise and wrapped around the pipe. At the same time, it is necessary to carefully monitor the coincidence of all seams between the wire and the insulation, which will help prevent the appearance of “cold bridges”.
5. Next, you should take plumbing tape and wrap the entire pipe very tightly over the insulation material. Remember that wrapping with plumber's tape is mandatory, as it helps prevent groundwater from penetrating through existing gaps.
6. After you have reached the places where the water supply system exits from the ground and enters the house, there is a need to use additional windings, which can be done in several ways: by additional insulation of cold water pipes using plastic film and by arranging a box frame around the pipes where it will be stuff insulation. The upper part of the box is also covered with a protective coating, for example, a wind- and moisture-proof film, sewn up after installation.

It is now increasingly common to install temperature data collection points along with the heating cable. It is enough to install 3-4 sensors on the highway so that you can monitor it manually or automatically.

For example, if the temperature drops below 5 degrees above zero, the system will turn on a voice alert and send a message to email or mobile phone. You can also provide for automatic activation of the heating system when the specified parameters are reached.

Liquid thermal insulation for pipelines

A completely new method of insulation is the use of special coloring compounds. Even a thin layer of such paint can replace 10-20 mm thick insulation . And if you apply the composition in several layers, you can achieve much better results. Heat loss can be reduced by up to 40% , while the coating does not allow water and moisture to pass through, but remains “breathable”. Liquid insulation is classified as energy-saving thermal paint and can be of two types:

• Ceramic , its consistency really resembles ordinary paint;
• As foam structure, which is applied to the desired surface by spraying.

The coating works on the principle of a thermos . The layer of material required for thermal insulation is very thin - only 0.5 mm . The advantages of this method of insulation include:

• When using the composition in the form of paint, its application simple and can be done with a regular brush ;
• If the coating chips or scratches form on it, it can be easily restored ;
• Low thermal conductivity;
• High elasticity , which allows the coating not to crack when the pipe diameter expands and contracts;
• Long service life;
• Health safety
• Condensation and corrosion do not form on the surface ;
• Possibility of application to surfaces of any configuration.

The disadvantages include:

• High cost of the composition;
• a foam composition as insulation , you will need to seek help from specialists . Which, as you know, provide their services only for large volumes of work. If you want to spray just a few meters of pipeline, you may simply not find a contractor.

Secrets of proper insulation of water pipes

It is definitely recommended to draw up a detailed diagram of underground water supply lines in the house and on the land, and also pay close attention to the connecting elements.

Remember that just one small drop of water that freezes in the threads can break them. And the pipes, in turn, should not be subject to corrosion; the best option is metal-plastic.

It is recommended to insulate and heat all sections of the pipeline that are at negative temperatures. This applies to rooms in the house, for example, unheated basements, and places where pipes enter buildings.

One of the methods for insulating water supply pipes in a dacha at the entry point is the following: place short sections of water supply up to 0.5 meters that remain uninsulated in pipes of larger diameter.

To do this, it is customary to use PVC sewer pipes with a diameter of 100 - 150 millimeters, sawing it lengthwise in advance. Next, you should center and secure everything with tape.

Drill several holes in height and fill the space between the pipes with construction foam from a can. As you fill, you can close the holes with the same tape.

Remember, warm water pipes in winter become objects of increased attention from various rodents - moles, rats and other living creatures. They can easily chew through insulation, asbestos and plastic pipes, considering them the most suitable warm place.

You can protect water pipes from them by plastering them with a solution of broken glass, wrapping them with a metal mesh, or using a metal sleeve.

This completes the pipe insulation procedure. If the instructions are followed correctly, the pipe will last a long time and at the highest level, without fear of severe frosts. I would like to remind you once again that insulation of the water supply system should be done in a timely manner, without waiting for a rupture to occur as a result of freezing water.

Always consider the water repellency, durability and fire safety requirements of the insulating material.

Source: strport.ru

How does the heating system work?

The system in any home is usually arranged like this. The water that passes through the pipes inside the building heats the air through radiators. It circulates through the pipes and returns to the boiler, which heats it to a certain temperature. But the important thing is that heating is necessary only in the building, and not along the length of all the pipes that may be located on the street. After all, sometimes the boiler room that provides your home with heat is located far from it, therefore, the pipes must run underground. You can read more about modern heating systems here. It’s very bad when all the heat that should heat living spaces goes out on the street or in the basement, where it’s also of no use. In order for the heating system to work properly, you need to ensure that heat is accumulated in the place where it is really needed. Then the pipes will not fail so quickly.

In what places should polypropylene pipes be insulated?

Compared to metal piping systems, plastic ones have significant advantages, which leads to lower heat transfer between the liquid and the surrounding air.

Insulation of polypropylene pipes will help avoid heat loss and, accordingly, cooling of hot water by 15-20%. For example, foamed polyethylene has a thermal conductivity coefficient of 0.036 W/mK, and polypropylene – 0.027 W/mK. The difference is obvious - 25% of heat can be saved when using this material.

All plastic pipes are subject to insulation, starting from the basement to the internal wiring inside the room. If you live in a multi-storey building with a technical floor (attic), then insulation there will also be necessary.

Heat loss in each room will be different, since it all depends directly on the air temperature. The basement will need maximum insulation. On the ground floor, stairwells and attic spaces, the insulation will be thinner and made from different substances.

Mineral wool

Thermal insulation using varieties of mineral wool has become widespread due to its affordable cost. With its help you can insulate heating pipes, hot water supply, water supply and sewer systems, as well as air ducts. This material works on the principle of a thermos. In addition, cotton wool protects the surface of the pipes from condensation. In the case of insulation of an underground pipeline, it is imperative to provide additional protection from moisture, so when wet, cotton wool loses its protective properties, and heat loss, in turn, increases. Mineral wool is a fibrous material for the production of which various raw materials are used. The most commonly used types are:

Glass wool - made from the same raw materials that are used to make glass. Its fibers are quite thick. For convenience, glass wool is available in the form of slabs, rolls or shells. To protect against moisture, one side can be covered with foil or a thin layer of aluminum. The thermal conductivity coefficient is 0.030-0.052 W/m*K. The material belongs to the NG class - non-flammable. When installing glass wool, you must be extremely careful and take care of personal protective equipment. Since with any touch to the material, small sharp particles fly in different directions, which dig into the skin even through fabric gloves

It is especially important to protect the organs of vision and breathing, since particles entering the lungs cause severe and prolonged swelling;

Basalt wool is made from molten rocks. It weighs more than glass wool

The material is also non-flammable and can withstand very high temperatures - up to 870°C. The thermal conductivity index is lower than that of the previous variety and is 0.035-0.039 W/m*K. Stone wool has a higher density and hardness. In this regard, the release form can be either in the form of plates or in the form of cylinders. An additional foil layer can be implemented on both forms;

Slag wool is made from waste from the production of cast iron. It is used quite rarely for pipe insulation. This is explained by the increased friability and acidity of the material, on the surface of which oxides form over time, negatively affecting the surface of the pipes. In addition, the material cannot be classified as environmentally friendly. And its thermal conductivity coefficient is quite high for a thermal insulation material - 0.46-0.48 W/m*K.

How to insulate polypropylene pipes

Insulation for pipes can be of various shapes and designs: wound, glued, in the form of a shell - oval, etc. There is a wide range of insulation materials, linings and ancillary insulation compounds available for use in hot water systems.

The list is constantly changing as new synthetic materials or application methods are developed. For example, the latest innovation in heating engineering is the use of antifreeze as a coolant for closed systems. It makes no sense to consider any specific manufacturer of insulation; you need to pay attention to the types of materials used.

Expanded polystyrene

Expanded polystyrene for pipes

This insulation is made in the form of two shells of different sizes; they are fastened together using special grooves, but to secure the connection they must be additionally secured with special glue or tape.

When connecting on pipes, the halves of the insulation are connected to each other and the two parts are shifted in different directions by several centimeters. The next link is also connected, and the remaining ends are joined together, resulting in a kind of “overlap” of one connection onto another, which provides a better bond.

To insulate awkward areas and corners, shaped shells that have unequal dimensions are used.

In order to carry out high-quality insulation with this material, you need to calculate in advance the length of the pipeline, the number of joints and bends. This is necessary to purchase the required number of connecting parts.

Insulation materials

Below is a list of the most commonly used materials for insulating hot water pipes, as well as a description of their main characteristics. For specific information on each type of insulation, visit the catalog of articles on our website. All insulating materials can be divided into 5 main types:

1. Honeycomb insulation is made up of small individual cells that are either connected or sealed from each other to form a cellular structure. The basis for such insulation is glass, plastic or rubber, and then various foaming agents are used. Cellular structure is further classified into 2 subtypes: as open cell (cells connected) or closed cell (sealed from each other). Typically, materials containing more than 80% air are honeycomb insulation.
2. Fiber insulation - consists of fibers of various materials of small diameter, among which a large amount of air is retained. The fibers can be organic or inorganic and are typically held together by a binding agent. Typical inorganic fibers include glass, stone wool, slag wool and aluminum oxide. Fibrous insulation is divided into wool or textile. Textile consists of woven and non-woven fibers and threads. Fibers and threads can be natural or synthetic. Basically, these are composite plates or rolls, not convenient for winding pipes, but very effective insulating, complete with reflective films.
3. Flake insulation consists of small particles, similar in structure to irregular leaves, that separate the surrounding air space and are easily formed into a specific shape. These flakes can be joined together with an adhesive base or poured into the required forms or covers without fastening elements. Vermiculite, or expanded mica, is a flake insulation.
4. Granular insulation consists of small round shaped particles of varying diameters that contain voids or are completely filled. These materials are sometimes confused with open cell insulation because the final bonded product has a similar appearance to foam insulation. Calcium silicate and molded perlite insulation are considered granular insulation materials.
5. Reflective insulation reduces the long-wave radiation that emanates from the pipes, thereby reducing the radian heat transfer emanating from the surface. Some reflective insulation systems consist of multiple parallel thin sheets or alternate layers to minimize convective heat transfer. Foamed polyethylene with a thin aluminum film (penofol foil) is the main and very striking example of reflective insulation.

In conclusion, let's look at one new insulation compound that is quickly gaining momentum and increasing its sales in the building materials industry. Thermal insulating coatings or paints are widely used for use on pipes, ducts and tanks. Currently, these paints have not been thoroughly tested, it is too early to judge the final effect. The available information comes only from manufacturers, without any laboratory tests or opinions of independent experts.

Insulation of pipelines according to SNiP

When carrying out work on equipment and installation of pipelines, it is necessary to comply with SNiP standards.

What is SNiP? These are building codes and rules for organizing construction production, compliance with standards, technical specifications and departmental regulations.

Basic norms and rules for thermal insulation

Heating networks are one of the main elements of centralized heating supply. You should strictly adhere to the rules and regulations when drawing up a pipeline thermal insulation project.

Subject to compliance with SNiP, thermal insulation of pipelines will be carried out efficiently without violating standards.

Thermal insulation of pipelines SNiP is provided for linear sections of pipelines, heating networks, compensators and pipe supports.

Insulation of pipelines in residential buildings and industrial buildings requires strict compliance with design standards and fire safety systems.

The quality of materials must comply with SNiP, thermal insulation of pipelines should be aimed at reducing heat loss.

The main tasks of thermal insulation, features of the choice of materials

The main purpose of thermal insulation is to reduce heat loss in heating systems or hot water pipelines. The main function of insulation is aimed at preventing condensation.

Condensation can form both on the surface of the pipe and in the insulating layer.

In addition, according to safety standards, the insulation of pipelines must ensure a certain temperature on the insulation surface, and in case of stagnation of water, protect it from freezing and icing in the winter.

Insulation of pipelines also increases the service life of pipes.

According to SNiP standards, thermal insulation of pipelines is used both for centralized heating and reduces heat loss from intra-house heating networks. What to consider when choosing thermal insulation:

• Pipe diameter. It depends on what type of insulator will be used. Pipes can be cylindrical, half-cylinders or soft mats in rolls. Insulation of small diameter pipes is mainly carried out using cylinders and half-cylinders.
• Coolant temperature.
• Conditions in which the pipes will be operated.

Types of insulation

Let's consider the most popular and frequently used materials for thermal insulation:

1. Fiberglass. Glass fiber materials are often used for above-ground piping because they have a long service life. Fiberglass has a low application temperature and is characterized by low density. High-quality fiberglass has high vibration, chemical and biological resistance.
2. Mineral wool. Insulation of pipelines with mineral wool is a very effective heat insulator. This insulating material is used in different conditions. Unlike fiberglass, which has a low application temperature (up to 180ºC), mineral wool can withstand temperatures up to 650ºC. At the same time, its heat-insulating and mechanical properties are preserved. Mineral wool does not lose its shape and is highly resistant to chemicals and acid. This material is non-toxic and has a low degree of moisture absorption.

In turn, mineral wool comes in two forms: stone and glass.

Insulation of pipelines using mineral wool is used mainly in residential buildings, public and domestic premises, as well as to protect surfaces that are subject to heating.

1. Polyurethane foam has a wide range of applications, but is a fairly expensive material. According to SNiP standards, thermal insulation of pipelines is environmentally friendly and does not affect human health. Polyurethane foam is resistant to external factors, non-toxic and quite durable.
2. Expanded polystyrene. In some areas of industry, foam plastic is an indispensable material, as it has low thermal conductivity and moisture absorption and a long service life. Expanded polystyrene is difficult to ignite and is an excellent sound insulator.
3. In addition to the above materials, pipeline insulation can be carried out using other less well-known, but no less practical insulation materials, such as foam glass and penoizol. These materials are durable, safe and are close relatives of polystyrene foam.

Thermal insulating paint can also provide protection against corrosion and high thermal insulation of pipes.

This is a relatively new material, the main advantage of which is that it penetrates into hard-to-reach places and is able to withstand high temperature changes.