The heat loss of sawdust-based insulation is slightly higher than that of modern materials.
However, in terms of the totality of their characteristics, they are not inferior to either mineral wool or polystyrene foam.
Next we will talk about:
- main characteristics of sawdust;
- their advantages and disadvantages compared to other insulating materials;
- methods of their use;
- using sawdust to insulate various parts of the house;
- choosing the most suitable binder for a given situation;
- reviews about insulation with sawdust.
Technical properties of sawdust
The quality of sawdust insulation is on par with other materials. It is characterized by the following technical properties:
- The raw materials contain only organic components that have a porous structure.
- Moderate degree of flammability.
- High level of thermal and sound insulation.
- Environmental safety, since the insulation is completely natural.
- Duration of operation – up to 40 years.
Sawdust is a cheap raw material that is used in buildings for various purposes. You can install it yourself.
Does it make sense to insulate a house with sawdust?
If the house is small, then using wood is acceptable. The cost of such a layer will be much cheaper than mineral wool or pinoplex.
However, it should be noted that wood waste is rarely used independently.
In order to extend the service life of the insulation, concrete and lime are often additionally used.
Wood shavings are safe for humans
Features of the material, advantages and disadvantages
Thermal insulation with sawdust is more often used in private low-rise construction. Raw materials have the following advantages:
- environmental cleanliness;
- low level of thermal conductivity;
- good sound insulation properties;
- low cost;
- ease of installation;
- light weight, so the load on the floor slabs is insignificant.
You can increase the service life of the insulation if you treat it with fire prevention agents, as well as antiseptics. Chips have disadvantages: they absorb moisture and can rot under its influence. Wood waste also has a high level of flammability. If sawdust insulation is laid in violation of technology, it can be damaged by insects and rodents.
Additional components can improve the properties when insulating walls or other parts of a building: copper sulfate, clay, lime, cement.
Preparing to start work
Before laying the insulation, you need to determine its thickness. This value depends on the construction area. In a wooden house that is used all year round, the thickness of sawdust for the floor will be approximately 30 cm. After this, it is better to calculate the exact volume of necessary materials so as not to encounter difficulties during the construction process.
For insulation work you will need:
- sawdust;
- lime;
- cement or clay;
- wood antiseptic (for example, boric acid);
- container for diluting the mixture;
- kneading spatula;
- watering can for spraying the finished mixture with boric acid.
Scope of application of sawdust insulation
Before insulating walls with sawdust, the pros and cons of the material are known; you need to know that they are also used to insulate ceilings, roofs, and floors. The technology for carrying out the work may differ slightly.
Walls
More often, wood shavings are used as wall insulation . Sawdust helps reduce building construction costs. First, wood waste is treated with a fire retardant, and chimneys, sockets, and switches are protected with fireproof material. Electrical wires in insulating tubes. The thickness of their walls is 3 mm.
To insulate the walls from the inside of the attic, you must first build a frame into which sawdust will be poured. Slats and wood lathing are fixed to the base. The best material for wall insulation has a coarse fraction. Additional components of the mixture are: water, lime, boric acid, cement. After preparing the solution, it should not crumble. By pouring insulation into the frame on the attic wall, it is compacted to prevent subsidence.
Floor
Sawdust is used as insulation to improve the insulating properties of the floor of a house or attic. The shavings are first prepared: left for about 2 months, mixed with binding components and an antiseptic solution. All insulation components are thoroughly mixed. The thickness of the insulation layer is at least 30 cm. If the attic room will be used only in warm weather or the temperature in winter is not lower than -20 degrees, then this figure is reduced to 15-20 cm.
When insulating the floor, the old covering is removed, and the joists and beams need to be checked for rotten parts or broken fragments. The frame is additionally coated with an antiseptic. The mixture for insulating the attic floor is prepared in small portions. When insulating a house with sawdust, heating pipes and electrical wires are additionally insulated.
The mixture with sawdust is placed on the covering material. After applying the insulation, it should be left for 14 days until fully matured. The attic is regularly ventilated during this period. After 2 weeks, the layer should be checked for voids and filled.
Floor pie during insulation
Insulation is not the only component of proper thermal protection of a structure. Sawdust requires preventing water and steam from getting on it, so waterproofing and vapor barrier will become additional layers. It is very important not to confuse their location, otherwise all insulation work will be pointless.
Insulating an attic with sawdust will require laying the components in the following order from bottom to top:
- floor design;
- vapor barrier;
- sawdust;
- waterproofing;
- attic floor.
Scheme for insulating an attic floor
When insulating the floor above a cold underground, the layers are arranged in a different order:
- floor design;
- waterproofing;
- sawdust;
- vapor barrier;
- first floor floor.
Scheme of floor insulation above a cold underground
Sometimes it is said that it does not make much difference which side the vapor barrier is laid on, but this is not true. Steam can penetrate into the insulation only from the side of warm air, so it is logical to install protection against it inside the heated room. Waterproofing, on the contrary, protects against condensation that falls from the cold air onto a warmer surface. Failure to comply with these rules will lead to disastrous consequences for the insulation and it will cease to perform its functions.
Ceiling
In addition to insulating the attic walls, the same procedure is carried out with the ceiling, since it is through it that up to 20% of the heat is lost. The rough base must be covered with glassine, and all wooden elements must be treated with protective solutions. Sawdust is poured into a solution of cement and water. Next, the mixture is placed on the surface of the floor slabs and compacted. The insulation process is carried out in warm weather so that the layer dries quickly.
For sawdust insulation to be of high quality, the shavings must be dry. It is better to use raw materials after they have been aged for at least 12 months. If you use fresh sawdust, the cement will not set. The chips must have a medium fraction. Raw materials are also checked for the presence of mold.
Roof
If the thickness of the roofing material in the attic is insufficient or the roof insulation is not done correctly, condensation appears on its inner surface, which has a negative effect on parts of the structure. Before insulating the structure, the wooden parts are impregnated with an antiseptic. Joints and cracks need to be foamed.
You need to spread roofing material between the beams, and the sheets are laid overlapping and secured with nails. Communications, chimney surfaces, and electrical wires are additionally insulated. To insulate the roof, you should choose fine insulation for the attic. In most cases, filling with sawdust requires the construction of a frame.
Thermal insulation of walls
Insulating walls is one of the most effective ways to maintain a comfortable indoor microclimate. Before starting work, you need to take care of fire safety.
For this purpose, the places where the wiring is laid are protected with special non-flammable materials. The wiring should be placed in a metal pipe with a wall thickness of at least 3 mm.
To fill the insulation mixture, a frame is installed, then wooden slats are attached to it, on top of which the sheathing is mounted. Sawdust is poured into the prepared structure and carefully compacted in order to avoid subsidence of the material in the future.
Dry method of laying sawdust
The installation process is carried out in two layers. For the first, coarse material is used, for the second - fine sawdust. To insulate the floor in the attic from the inside with your own hands, you need to proceed as follows:
- lay film insulation on the joists;
- fill the subfloor from boards;
- lay an additional layer of insulation;
- pour sawdust and compact well (each layer is done separately, and its thickness is 10 cm);
- Dry the material for 3-4 days, after which the shavings are covered with waterproofing.
The last step is to finish the floor. To insulate the walls, sawdust will need to be mixed with a binder. The drying process of the layer takes 2-3 weeks.
Which sawdust to choose
Going into the forest to cut down a tree and use it for sawdust is not the best option. There are many other ways that cause minimal harm to nature and are more intelligent. Sawdust obtained during carpentry is ideal for insulation. This material has good moisture content and is less susceptible to damage by mold, mildew and insects.
Sawdust is available in large quantities at sawmills. They are waste of wood that has not yet dried, so their characteristics are worse than those of the previous ones. But such material can also be used to insulate the floor in a wooden house.
It is best to choose small chips. They will be able to provide the most effective thermal insulation.
Application of auxiliary astringents
In order for the insulation to be of high quality and durable, sawdust must be combined with binding components. They will not only reduce chip consumption, but also improve its technical characteristics.
Lime
If the owner cannot decide which insulation to choose for the attic walls so that it is cheap and effective, you can fill the frame with sawdust and lime. Well-dried shavings are mixed with the second component in a ratio of 10:1. Additionally, an antiseptic is added to the composition (25g per bucket). The solution is placed in a pre-prepared frame or space between the walls and compacted. But you shouldn’t tamp it too hard, as this can worsen the technical characteristics of the material.
The use of sawdust with lime as insulation provides good insulation, and the powder increases the fire resistance of the mixture and its resistance to damage by rodents and insects. This method can be used when arranging the floor if laying a plank structure is planned.
Gypsum
A mixture of sawdust and gypsum retains heat well and is light in weight. But she is afraid of water, so when using the material you need to take care of its waterproofing. To prepare the solution, take 8 parts of shavings and 1 part of gypsum. It should be mixed in small portions so that the entire amount of material can be applied. Liquid is added at the rate of 0.7 liters per 1 kg of gypsum. You can also use components that slow down the hardening of the solution.
Cement
You can insulate the attic base with cement mortar and sawdust. An additional component is lime. To prepare the mixture, the following components are taken:
- 10 buckets of shavings;
- 1 bucket each of lime and cement.
After mixing the components, the solution is irrigated with an antiseptic. It should retain its shape well, but not release water. Only in this condition is the use of sawdust with cement as insulation justified. It is better to make blocks from the resulting solution, which are used to insulate walls, roofs, and floors. It takes 2 weeks for the layer to dry completely.
Clay
To make warm plaster, you can mix sawdust with clay, cement, old newspapers and liquid. The substance is most often used to insulate the internal surfaces of attic walls. It is difficult to prepare such a solution manually, so it is better to use a concrete mixer. It should have a medium degree of thickness. You should not add a large amount of shavings, since after drying the clay shrinks greatly.
Before laying the mixture, the base must be covered with waterproofing. The insulation layer is 10-15 cm. It will take 3-4 days to dry. If cracks have formed on the surface during this time, they can be eliminated using wet clay. The solution is applied to a vertical surface in the same way as plaster. The surface of the base is cleaned of dirt, dust and loose fragments.
PVA glue
An insulated house or attic will save money on heating. In addition to the previously mentioned binding components, PVA glue is used. A construction or universal type of substance is better suited here. Sawdust can be fresh, but must be dry. The mixture must be used within 1.5 hours after preparation.
If lightweight insulation is needed, then a smaller amount of glue should be used, although the ratio can be 1:2 or 1:10. To increase the strength of the insulator, you can add a little cement to its composition. To the question: is it possible to use sawdust with PVA glue to treat walls, the answer is clear - no, since the mixture has a low level of plasticity.
When filling the space between the wall and the facade, the internal surfaces are covered with drying oil or a thin film.
Video on the topic
The detailed process of making building blocks from clay with sawdust and sawdust concrete (with the addition of cement) can be seen in the author's video below. Thank you for your attention.
Blocks of sawdust concrete and clay with sawdust. New idea.
Andrey Vasiliev
Ask a Question
Building materials using sawdust
Sawdust is used not only for insulation of walls and other parts of the attic, but also for the production of building materials with good insulating characteristics.
Sawdust concrete
Sawdust concrete contains fine shavings, lime, cement and sand. Its density depends on the ratio of the components. Depending on the technical characteristics, the product is used for the construction and insulation of internal and external walls of dachas, cottages, residential buildings, attics, garages, and outbuildings. Fences or pillars for them are built from sawdust concrete and used to strengthen the foundation.
The material is well processed; various decorative materials can be used for its finishing. If it is manufactured in accordance with technological requirements, then its properties include high fire resistance and resistance to low temperatures. Sawdust concrete provides good sound insulation of attic walls, is easy and quick to install, has a low cost, but slowly gains strength and requires reliable protection from moisture.
Arbolit
Arbolite blocks are made from a mixture of wood chips, cement, and sawdust. The advantage of the product is its high thermal insulation property, strength, and fire resistance of the walls. The block is easy to process. Wood concrete does not crack, even if it is not stored under a canopy, but is subject to slight shrinkage. The product is relatively light and environmentally friendly.
The disadvantage is the inaccuracy of the geometric shape and low resistance to moisture. For finishing wood concrete, only those products that can allow air to pass through are used.
To understand which insulation is best for the attic, you need to decide on its purpose and seasonality of use. Using sawdust, you can well insulate a given room and ensure its impeccable technical characteristics for many years.
Why is sawdust not used for insulation in its pure form?
Despite the fact that clean sawdust reduces heat loss well in any building, it has three serious drawbacks:
- They cake over time, which is why voids appear in the insulating layer, which have a higher heat transfer coefficient.
- Wood sawing waste is a very attractive place for various rodents that settle in it.
- Pure sawdust can only be used to fill a clearly limited space, so it cannot be used to insulate walls without voids.
Normal compaction of sawdust is impossible without strong moisture, which sharply reduces their thermal insulation properties .
Therefore, when filling this material into the pockets intended for them, you have to put up with the possibility of voids caused by the compaction of sawdust.
In places of such voids, cold bridges appear, which leads to the appearance of cold sections of the walls and increased heating costs.
Another disadvantage of this material is that it attracts rodents .
Indeed, in its structure, waste from sawing wood is very similar to soil, so mice and rats dig holes in it and begin to multiply intensively.
After this, the rodents make passages to different rooms and begin to feel very at ease in the house.
The third disadvantage is due to the fact that sawdust cannot hold its shape on its own , so it cannot be used outside or inside the wall.
These three disadvantages greatly limit the scope of application of this material.
But the combination of wood sawing waste with various types of binding materials not only reduces, or even completely eliminates, the described disadvantages, but also allows you to successfully compete with the most modern insulation materials.
