Baxi brand boilers are one of the best options for equipment used in arranging heating systems. Various configurations of this modern thermal equipment have been developed; accordingly, potential users are provided with fairly comfortable operating conditions.
However, like any other electronic-mechanical devices, this type of equipment is not completely immune from malfunctions. Technical documentation mentions possible failures of various types at least 99 times.
How are faulty phenomena expressed, what numbers accompany Baksi boiler errors, and how can you fix the problem at home? Let's look at this issue in our article.
Decoding
The factory interpretation of error E25—reduced coolant circulation—does not provide a complete understanding of the essence of the problem. In the instructions for various models of the Baxi boiler, the emphasis is on blocking the pump. But this is not the only reason such a fault code appears on the display.
Control panel for gas boiler Baxi LUNA 3 comfort
Error e25 indicates an intense increase in temperature in the heating circuit. This parameter in Baksi units is determined by the difference in readings from sensors installed at the inlet and outlet of the boiler heat exchanger. When it grows at a speed above 1 0С/sec, the operation of the unit is blocked by the protection circuit. A decrease in fluid circulation is caused by several factors, therefore there is no clear recommendation for eliminating error E25. The algorithm of actions given in the article will allow you to figure out the reason for the appearance of this fault code in a short period of time.
Baxi boiler error 25. Heating circuit temperature sensor
Regardless of the reasons for the error, it is detected by the temperature sensor, so its malfunction is also possible. There may not be actual overheating - the sensor simply provides incorrect values to the control unit. Typically, sensors are thermistors with a certain dependence of resistance on temperature. Therefore, it is quite easy to check the serviceability of the sensor - measure its resistance with a multimeter. At room temperature it should be approximately 10 kOhm, at 40 degrees approximately 5 kOhm. In some boiler models, the heating and hot water temperature sensors are the same, so they can be swapped for testing (for testing only!). If necessary, buy a new temperature sensor.
Other malfunctions and solutions
In addition to those described above, other codes may appear on the display during operation:
- E111 - appears when the supply fluid is heated above 95 degrees. Press and hold the Reset button for a couple of seconds. If the value does not disappear, you need to call service.
- E129 - fan speed is below the minimum permissible. You need to contact a service center for repairs.
- E153 - accidental pressing of the “Reset” button. What you need to do to set the previous mode is just press and hold this button until the settings are restored.
- E154 - lack of flow circulation. To resolve the problem, contact customer service.
We invite you to watch a video about eliminating error E03 on a Baksi boiler:
Useful observations
- To ensure uninterrupted operation of the Baxi boiler, connect it to the network via a UPS. The UPS contains a charger, stabilizer and battery group. This ensures continued operation of the device even in emergency situations. The number of additional working hours can be determined by the total capacity of all batteries.
- If the boiler is controlled by an electronic board, before operating it you need to check in the settings whether the type of heating device is selected correctly. An incorrect choice can trigger error E25.
- The Baxi boiler may display error E25 after changing the heating circuit. An installed radiator can cause a large load on the pump. The hydraulic resistance increases, which reduces the circulation in the boiler - this is how fault E25 occurs. This point must be taken into account before reconstructing the heating system. To prevent the problem, you can include an additional pumping device in the circuit, determining the correct characteristics and a suitable installation location.
- If the heating system needs to increase the pressure from time to time by topping up, the problem is caused by a small leak of liquid due to a crack - therefore, the coolant level decreases gradually. If the pressure drops and diagnostics do not yield results, you need to look for a hidden leak.
- When replacing a unit, check the identity of the numbers and letters on the panel. When replacing the board with a universal unit, you need to adjust the boiler settings.
- When installing the NTC, you should change the gasket and apply fresh thermal paste to the internal circuit tube.
Errors E25 and E26 for the Baxi boiler are similar, but they can be caused by different reasons. If you find it difficult to identify the problem yourself, it is better to seek help from specialists. Sometimes even experienced professionals cannot immediately accurately determine the problem - it takes time and checking possible options.
The most common causes of errors during operation
Errors in Baksi gas boilers are displayed on the display as coded messages. To decipher the message, you need to use the correspondence table. It is worth noting that each model has its own, so it cannot be used as a universal one. This can lead to an incorrect diagnosis and the prescription of useless actions that will not be aimed at eliminating problems.
Malfunctions of Baksi wall-mounted gas boilers with one working circuit will affect exclusively the heating system. Moreover, electronics break down more often, because mechanical parts are made of durable metal, which undergoes additional processing and hardening. As a result, it can last for many decades without even showing visible signs of wear.
When cleaning the combustion chamber, you need to remove the naga very carefully so as not to damage the protective inner layer. If this happens, the wear rate will increase many times and the boiler will not be able to work for the entire announced period of time. You should behave in the same way when cleaning the burner. The diameter of the tool should be smaller than the holes so that they do not become loose, otherwise the device will become unusable and will have to be replaced.
Malfunctions of Baksi double-circuit gas boilers will already affect both the heating and water heating systems. There are many more options for breakdowns here, since the system is more complex than a single-circuit model. Diagnostics can take more time, and repair work is much more difficult. So in this matter, it would be better to trust the professionals so that they take on all the troubles themselves.
To avoid breakdowns and extend the life of the unit, you need to correctly configure the Baxi gas heating boiler. This is quite easy to do if you use the practical recommendations from the instructions. In addition, the “smart” automatic control system itself will prompt the user with the optimal parameters that are best suited for his system. In general, you need to carefully monitor the automation readings, as they can tell you about impending problems. Timely diagnosis increases the chances of success.
Content
- Instructions for installing a baxi boiler What needs to be done
- Error E 01
It has already been proven that the safest and most effective heating occurs through the condensation of water vapor generated during the combustion of hydrocarbons. Gas boilers that operate using such a system are called condensers. This is exactly what Baxi belongs to, which is designed for the conditions of post-Soviet countries. In Russia, Ukraine and Belarus, it is important to use energy-saving technologies, which is what the manufacturer of gas boilers Baksi does.
BAXI Forum
The largest professional forum BAXI in Russia
- Unanswered topics
- Active topics
- Search
- Users
- our team
- Acknowledgments
- 04/16/2021 — The conference has been moved to a separate subdomain. Now we are at forum.baxi.ru.
- 11/15/2019 — A separate section on the forum has been allocated for discussion of the ZONT device.
- 07/19/2019 — The BAXI seminar book 3Q was published. 2019 (119 MB). Download
- 06/20/2019 — BAXI Energy voltage stabilizers are on sale.
- 04/16/2019 — Sales of BAXI Eco Nova boilers have started.
- 11/16/2018 — The BAXI 4Q seminar notebook was published. 2018 (8 MB). Download
How to fix the error. Instructions
- Before starting work, you need to turn off the boiler, turn off its power and shut off the gas supply.
- It is necessary to check the filter located on the return line of the heating system. It is necessary to close the taps and drain the water from the boiler. To do this, place the drain pipe on the tap fitting on the left and turn it to drain the water. After this, the drain valve is closed.
- Next, you need to check the filter, which is located on the return line of the heating system. Unscrew the plug, inspect the mesh that is located inside, and if necessary, rinse and clean it. Then the filter is put in place and fixed.
- Then the boiler is disassembled. To remove the front panel, use a Phillips screwdriver and remove the two screws from the bottom. The panel is pulled towards itself and removed from the fasteners.
- It is recommended to check the filter on the heating system. Expand the control panel. The filter is located in the hydraulic group under the circulation pump. Dismantle the electric drive for the directional valve: remove the bracket and take out the electric drive itself. Then you need to carefully pull out the capillary of the heating system pressure gauge. Next you need to remove the bracket that secures the filter itself. Then, by prying from below with a small screwdriver, you can remove the filter element. If the filter is dirty, it needs to be cleaned. Before installing the filter back, it is recommended to lubricate the o-ring with a special lubricant - this will help avoid problems during further dismantling if the filter has to be removed again.
- After lubrication, the filter is put back and secured with a bracket. The pressure gauge is also connected to its original place, the valve drive is installed and fixed.
- Next, open the taps for the heating system and feed the boiler. Pressure is raised to feed the boiler. Close the tap.
- After the work has been done, you need to check the circulation in the boiler. Fix the control panel, open the gas supply valve, connect the power supply and turn on the boiler. After starting the fan and turning on the pump, the boiler will start working and it will be possible to check its circulation. If the boiler works well and does not display an error, the problem is solved and the operation of the device is restored.
Thus, the error for the Baxi E25/E26 gas boiler model is associated with clogged filters. To eliminate it, you need to dismantle the device and clean the clogged areas. After this, the boiler’s operation will be restored.
