Chimney lining is carried out in cases where the previously built brick chimney of a stove or fireplace began to lose its throughput, often becoming clogged with combustion products. At the same time, the draft is significantly reduced, due to which smoke periodically fills the rooms of the house, and the heating efficiency sharply decreases.
Chimney lining
There are several ways to solve this problem. But one of the most effective is to “ennoble” the internal surfaces of the brick walls of the chimney shaft with special liners. These sleeves have smooth internal surfaces, so that smoke does not encounter obstacles and does not linger in the channels. It smoothly “slides” along the smooth walls, coming out, while leaving virtually no fuel combustion products on the surface of the liner.
Types of lining
Lining with a sandwich pipe
The principle of behavior of lined liners and their placement in the channel is the same, but the sleeves differ in material, so there are certain nuances for each type.
Specialized stores offer inserts:
- made of polymers;
- of steel;
- from corrugated pipe;
- polymer sleeve;
- made of stainless steel.
Polymer sleeves
A plastic pipe is installed inside the operated chimney. PVC products are reinforced with fiberglass fabric and, when heated, acquire plasticity. As a result of this property, irregularities and spaces on the clinker surface are filled. After hardening, the internal area becomes smooth, and the wall has a thickness of 2 cm.
The downside of the application is the temperature limitation. Lining a chimney made of brick with plastic is done with exhaust flows up to +250°C, so they are installed to work with low-power units.
Application of steel elements
Corrugated pipe lining
A structure made of a rolled pipe is placed in the straight section of the chimney, or rectangular, square, oval and round shapes are made with your own hands. Sheets are taken with a thickness of 0.5 to 1.5 mm. In channels made of steel materials, it is possible to provide the required modules for cleaning, inspection, and containers for accumulating condensate in accordance with the standards.
Steel products are used for fireplaces using various types of fuel. The material resists acids and is not subject to plaque deposits. The disadvantage is that only straight sections can be lined with this method; winding pipelines cannot be equipped.
Using corrugated pipe
Manufactured using various types of stainless steel, the pipe shells are made of two layers. The positive thing is that flexible liners are used for complex channels with turns. The products do not require connecting elements. Double-layer inserts significantly reduce the diameter of the air duct; this must be remembered when choosing.
Polymer sleeve
Polymer sleeve for chimney lining
The sleeve is made of copolymer resin and reinforced with fiberglass. The insert is used to combat condensate drops; it is used to treat low-temperature chimneys and those coming from powerful boilers.
Types of polymer products:
- Fitfire is a liner containing two layers, the maximum element has a length of 60 m. After installation, the chimney duct has a diameter of 80 - 500 mm. The manufacturer specifies a service life of 50 years; the hose is used to remove low-heat gases.
- Fitfire HT 1000 is used in pipelines of sauna and fireplace hearths with high smoke heating. The sleeve consists of three layers, the middle one is a reinforcing mesh.
When lining the chimney with a polymer sleeve, the internal protection is obtained without seams, with a smooth surface.
Stainless steel pipe
The material is one of the most popular types. The products work for many years and do not deform due to high temperatures or corrosion. Lining a brick chimney with a stainless pipe is often used because... There is a large assortment of ready-made inserts for sale, sometimes products are made by hand, taking into account the dimensions.
The inserts are made from stainless steel sheets with a thickness of 0.8 - 1.5 mm. To connect and turn the channel, standard tees and pipes are used, but to install them you need to know the exact layout of the chimneys. Sleeves with a rectangular cross-section are installed only on straight sections of chimneys.
General description: what is Furanflex?
To understand what Furanflex is, let's start from the very beginning. A chimney is a duct (pipe) that runs from a stove, fireplace or boiler through all of these to the top and out through the roof. Very often the chimney duct is made of brick.
A sleeve (sleeving) is an insertion of a pipe made of a different material into a brick chimney. At the exit we have a pipe in a pipe, and in this case the smoke will not come into contact with the brickwork, but with an additional pipe placed (a sleeve, which is usually made of ceramics, steel and a polymer sleeve).
Pipe lining with Furanflex
A correctly installed sleeve protects the chimney channel from fouling with soot, and also protects from condensation and exposure to high temperatures. As a result, the service life of the channel is significantly extended, and the likelihood of its breakdowns and blockages is reduced.
During installation, it is unwound, lowered into the chimney channel, straightened along the entire length and secured at the top (at the pipe outlet) and at the bottom (at the place of attachment to the stove). Next, a plug is placed on the hose from below (it is blocked), and a special installation is connected from above, through which hot steam is supplied to the hose.
Under steam pressure, the hose expands along its entire length, pressing against the walls of the air duct. Under the influence of temperatures, the sleeve becomes elastic and is then glued to the brickwork, at which point the installation process ends. At the same time, both fireplace and stove chimneys can be lined in this way.
Where and what is it used for?
Furanflex is used for lining, that is, to protect the main chimney channel. Moreover, even if the protective liner fails, replacing it is both cheaper and easier than replacing the main chimney duct.
The use of Furanflex is justified in the following cases:
- To protect the smoke channel during its construction.
- To protect an existing smoke channel.
- To restore a smoke duct that has become unusable (and it usually doesn’t matter what exact reason led to the failure of the smoke duct).
Typically, lining in this way is used for lining chimneys located in low-rise private buildings. Somewhat less often - for channels located in baths or saunas. But there is no prohibition on the use of this technique for chimneys in industrial systems.
Material and characteristics
The Furanflex protective sleeve consists of several structural elements (layers or segments), so it makes sense to consider them all.
Sleeve segments:
- internal segment - made of thermoplastic polyethylene, used exclusively at the installation stage and used to hold the middle layer (segment) - after installation it is immediately removed from the channel;
- middle segment - made of thermosetting polymer resin using fiberglass (330 g per square meter), and there are usually several layers of fiberglass (about four);
- outer segment - made of polyester fabric (if we are talking about Furanflex Black or Ventiflex), or from fiberglass with Kevlar reinforcement (if we are talking about Furanflex RVW).
General information about Furanflex material
Product Specifications:
- Basic length: up to 30 meters.
- Basic sleeve diameter: from 60 to 1000 millimeters.
- Wall thickness: from 2 to 3 millimeters.
- Tensile strength: exceeds 400 N/mm.
- Maximum smoke temperature (with prolonged exposure): up to +250 degrees (if we are talking about Furanflex Black), or up to +700 degrees (if we are talking about Furanflex RVW). One-time short-term temperature rises up to +500 for the Black model and up to +1000 for the RVW model are allowed.
- Maximum channel bend angle: 45 degrees.
- Minimum ambient temperature: no more than -50 degrees.
- Service life: from 10 to 30 years with proper installation and subsequent operation.
Briefly about the manufacturer
The Furanflex company is based in the Russian Federation, and its products are aimed specifically at the CIS market. The company has a representative office in Ukraine.
Considering that the described products are rare in the construction market of the CIS countries and the choice of them is small, the Furanflex company can be called a fairly large manufacturing company of such devices. This is the largest manufacturer of chimney hoses and the most popular in Ukraine, Russia and Belarus.
What is lining a brick chimney?
During the operation of brick chimney channels, soot accumulates in them, which affects the deterioration of draft in the system. Brick chimneys have rather rough walls, so they are prone to soot accumulation. Brick communications for the removal of combustion products are easily destroyed due to various negative factors affecting them. Consider these factors:
- temperature changes;
- condensation that appears due to temperature differences during operation of brick chimneys;
- aggressive chemical compounds contained in smoke.
As a result of the accumulation of soot, the draft in the system deteriorates, which, in turn, affects the performance of the heating structure. As a result, a reverse draft effect may occur, which will lead to smoke in residential premises.
This effect poses a great danger to the health and life of the owners of the house, therefore, to ensure safety, it is very important to carry out preventive checks and cleaning measures on time
Installing a liner in a chimney does not entail the same costs as completely replacing the chimney
There are two main ways to solve the problem of soot formation in a brick chimney duct:
- chimney lining;
- complete dismantling of the old channel and installation of a new chimney communication.
Since the second option is much more labor-intensive and entails large financial costs, many people line the chimney.
Is there a need for a sleeve?
It is better to install the sleeve during the construction phase of the building. The insert is bricked up as the shaft is laid out from brick. If you didn’t do this initially, you will have to return to the process over time. Cladding a completed house is more difficult. We will have to partially destroy the masonry, break the decorative cladding and restore everything again.
The urgent need for lining brick chimneys is caused by the following reasons:
- Initially, the combustion product removal system was designed and built with errors;
- constant use of a fireplace or stove connected to a brick chimney is assumed;
- long channel length;
- if according to the project the mine should be lined, but this was not done;
- the shaft passes through a cold attic and due to the temperature difference, condensation forms;
- the chimney is made of brick inside the outer wall of the building;
- condensation streaks appear from the seams of the brickwork of the shaft;
- depressurization of the smoke channel;
- the shaft quickly becomes clogged with soot and requires frequent cleaning;
- The smoke exhaust passages were laid not by professional stove makers, but by inexperienced masons.
In all other cases, the owner performs the sleeve at his own request.
Main rules for lining
Lining a brick chimney with a stainless pipe is not such a complicated process. But let's talk about everything in order:
So, as a rule, this method is used to smoothly restore the removal of processed gases. This is especially true when the owners do not have the opportunity to remodel the entire chimney duct.
There are two sleeve methods:
- Stainless steel sleeve;
- Liner using the FuranFlex system (here a special polymer liner is used, which is “blown” into the chimney, and which, when hardened, becomes a new chimney).
https://youtube.com/watch?v=VAFq-N889jY
Nuances and requirements for lining the chimney of a gas boiler
Before lining, you need to clean the brick chimney from soot.
A chimney lining is a necessary solution if the pipe is made of brick. The presence of the insert does not protect against the appearance of condensation drops, but with the help of the lining it is possible to ensure organized moisture removal.
Before lining a brick pipe, you need to prepare:
- inspection of the chimney outlet;
- checking the section shape;
- identifying the degree of contamination;
- pipe cleaning;
- checking for tightness and functionality.
The cross-section is most often represented by a rectangle with dimensions of 14 x 27 cm; before installation, the dimensions of the sleeve, its length and shape are determined. Attention is paid to the cross-sectional area, because the insert in the channel narrows the outlet.
Work rules
In this article we will look at how chimney lining should be done. This is not very difficult, but necessary work. As a rule, chimney lining is used to restore the unhindered removal of exhaust gases when it is not possible to redo the entire chimney duct. The chimney liner can be made in two ways:
- installation of steel sleeves (preferably stainless);
- use of the FuranFlex
, which is suitable only for gas boilers with low combustion product exit temperatures.
Preliminary work
Additional measures before chimney liner:
- Identify all damage, including brickwork. Check the strength of the entire structure.
- Inspect for tightness and integrity, the degree of clogging of the chimney.
- Inspect the cross-section of the pipe and the absence of any obstacles along the entire length of the channel.
- Determine the cross-section of the pipe and compatibility with the intended sleeve so that the chimney itself does not narrow.
- Before carrying out, determine the complete design of the future sleeve.
- Provide free access to the work site.
When carrying out pipe laying work, you must:
- Dismantle the brick wall of the channel in the place where the heat generator will be installed. The length of the disassembled surface must correspond to the length of the elements that ensure the collection of condensate, provide for the installation of a hatch for cleaning and a smoke exhaust pipe.
- Install the specified elements in the channel (see).
- Attach ropes of the required length that have sufficient strength to the straight part of the pipe (which has hooks).
- Place the inserted pipe in the brick channel at a height so that it is possible to insert another nozzle.
- Lowering the rope, fasten the following pipes until the channel distance is completely covered.
- Fill the voids between the pipes and the walls of the brick channel with non-combustible heat-insulating material.
- Install the pipe on the head of the brick channel. Attach an umbrella to protect from precipitation.
- Make a brick backfill for the dismantled chimney opening.
Lining with flexible stainless pipe
The chimney can also be lined with a flexible stainless pipe. True, this will not be the best option. This pipe has its disadvantages:
- the corrugated surface does not interfere, but helps the accumulation of condensation and soot;
- small wall thickness reduces the service life of the structure.
So it's not ideal.
They also line the inner surface of the channel with a fire-resistant mixture
. It fills all the cracks and levels the brick surface of the chimney. In this case, the channel practically does not decrease.
If the height of the chimney duct is high, a technological hole is made in its lower part, which is laid after finishing the lining work. The cost of such work will be significantly lower than lining, but will never guarantee good tightness of the channel.
The simplest option is to install a liner during the installation of the chimney, during the construction process. This will increase the reliability of the channel at no additional cost. But many do not take this issue into account during the construction process, and this is a significant mistake.
These problems in brick houses are completely solvable. Remember, the safety of your home and the health of your family depend on the proper operation of the chimney.
During the operation of chimneys, you may encounter the problem of deposition of combustion products, or simply soot, on its walls.
A bathhouse in which cracks appear in the chimney, or, worse, partial destruction, ceases to meet fire safety requirements.
This can happen due to improper use, errors in choosing the material from which it is made, or deviations from building codes during its construction.
Another of the most common signs of malfunctioning chimneys is the appearance of “backdraft”, which is not just annoying, but deadly due to possible carbon monoxide poisoning.
How to vent a chimney through a wall?
The best option would be to exit the chimney from the gable side. If the heating equipment does not allow such an installation and the chimney pipe will exit from the side of the roof slope, then it is necessary to assemble a support post to which the chimney will be attached with sliding fasteners. If the roof overhang is more than 40 cm, then it is quite possible to do without such a rack.
In this case, the chimney can pass through the roof overhang, where additional fixation of the pipe can be arranged
It is also important to install snow guards above the chimney exit point. They will protect the chimney from damage due to snow.
How to remove a chimney through the roof, video instructions:
If a wooden house will be covered with siding, then it is worth keeping in mind that most manufacturers of this material indicate an operating temperature range from -50 to +50 degrees
Therefore, it is necessary to install the chimney so that the distance to the facing material is at least 15 cm. The place where the pipe exits through a wall covered with siding must be additionally protected with heat-insulating material.
Installation of a chimney is a fairly important stage in the construction of a private house (read: “How to properly build a chimney in a private house”). Therefore, before starting work, you should prepare and understand the most important aspects of installation. Not only the functionality of this element, but also the efficiency of the entire heating system depends on the correct installation of the chimney. Only full compliance with fire safety requirements and chimney installation rules can ensure its proper operation.
Causes and consequences of chimney pipe destruction
Artificial destruction may include: poor-quality illiterate masonry; low-grade materials used in the work; improper operation; low qualification of the stove master; non-compliance with the rules and construction plans.
This chimney is in need of repair.
If work is carried out incorrectly, condensation may form in the chimney pipe, and with temperature changes and freezing of water, ice will rupture the mortar in the masonry and destroy the bricks. After such processes, it is possible that the draft may be disrupted, which means that it will be impossible to light a fireplace or stove, since the smoke will not go up the chimney, but will go into the room.
Obvious delamination of low-quality bricks
If low-quality or untempered brick is used, it can be damaged by sparks or ignition of gases emanating from the firebox. In the future, these destructions can lead to damage to the entire stove heating system or even to a fire.
Repair of a brick chimney is carried out in cases where it is damaged for other reasons - for example, due to the consequences of natural phenomena or mechanical impact, which led to a violation of the integrity and solidity of the masonry.
Fatal effects of time and nature
Natural causes of destruction include the above-mentioned long-term use, and, as a consequence, the general aging of the structure.
Requirements for the exhaust duct
Good traction is maintained due to the tightness of the structure, as well as the condition of low soot accumulation and condensation formation. These parameters are the basic requirement for all chimneys. It is important to correctly calculate the cross-section so that there is no smoke inside the room.
Stage 3. Head construction
After the main installation work on lining the chimney with your own hands, we proceed to the design of the mouth of the lined chimney. This process requires adherence to the following rules:
- The sleeve/case insert must rise above the smoke shaft;
- A cover plate should be installed around the sleeve that protrudes (if there is none, a tile is made of metal or of cement-sand mortar with a slope away from the pipe itself);
- It is necessary to install a cuff near the pipe to prevent moisture from getting between the pipe and the shaft. Or arrange a mortar ledge with a gap for expansions;
- The direction of the pipe mouth is vertical, cut is horizontal;
- The protruding part above the roof and in the attic must be thermally insulated;
- It is advisable to install an umbrella that will prevent precipitation from entering the pipe (which is especially important when the condensate drain is not connected to the sewer);
- To increase the height of the pipe and further design it, it is better to use sandwich pipes with factory-made parts;
- Thermal insulation of sleeves should not be carried out with bulk materials, this is not permissible;
- To make ventilation channels, a cuff with a cone is used, or vents are made in the surfaces of the shaft (side), below the cover plate.
Features of transition of sandwich pipes in floors
In size, such a structure must exceed the thickness of the ceiling by at least 70 mm. It is these parameters that make it possible to ensure high-quality protection of the ceiling from fire.
In this case, you need to pay special attention to the quality of the box fastening
It is important that the pipe mounted in the box does not have joints. Before directly installing the dividing box with your own hands, you need to correctly mark it
It is possible to make a hole in the ceiling only if the dimensions of the box are known and the pipe in it is correctly located.
After the box with the pipe is installed, it is properly insulated. For this purpose, it is better to use basalt mats with a foil base. The hole made in the ceiling is also subject to insulation. For this purpose, mineral wool or other heat-insulating material that is not subject to fire is used.
Why do you need a chimney?
You can look at the photo of chimneys for a solid fuel boiler or traditional fireplaces with stoves. They are, in fact, very similar, because they have the same purpose - eliminating combustion products during operation of the heating boiler.
This happens due to the draft, which is created due to the difference in temperature and pressure of the air that is inside the heating boiler and outside.
In the winter season there should be no problems with this, and absolutely none, because the temperature outside will be very low, mostly sub-zero, but the temperature inside the boiler can in some places exceed 300 degrees Celsius.
In the case of gas boilers, we simply get air without oxygen - carbon dioxide, which we cannot breathe, but it becomes terrible only in high concentrations.
If in the case of gas the chimney is more of a ventilation duct, then in a solid fuel boiler there are many substances that exit through the chimney, outside the system and the house.
Holes in the chimney can pose not only an aesthetic threat, but also be really hazardous to health, because carbon monoxide and smoke flow through it, in fact.
Features and design of the chimney
The design of a brick chimney coming from a fireplace, stove, solid fuel and gas boiler is a shaft that forms a straight channel or a channel with turns. The upper part of the structure is raised above the roof, and a protective cap is placed on top.
Principle of operation
When the boiler is burning, the temperature at the bottom of the duct is higher than at the outlet. Due to the difference, a pressure difference is formed. The higher this indicator, the better the traction. Combustion products are freely discharged to the street, and oxygen enters the firebox to support combustion.
Approximate cost of work
The cost of rehabilitation depends on the materials and design of the future chimney liner. For installation of a 1 m long liner you will have to pay approximately 2.5 thousand rubles. After measuring the length of the shaft and multiplying the results by the cost of the selected liner, you can roughly calculate the cost of rehabilitation.
We hope that the information provided will help you choose the appropriate sleeve method and complete all the work yourself. We invite you to subscribe to other useful articles. Share information on social networks. Maybe some person is similarly looking for ways to solve a similar problem.
What are the reconstruction methods?
There are two ways out of this situation:
- Reworking the chimney shaft.
- Lining (sleeve, insert) of the smoke exhaust channel.
Let's consider each option separately.
Relaying a smoke exhaust pipe involves significant financial investments: dismantling or disassembling the channel, purchasing new material, delivering it to the reconstruction site, loading and unloading work and paying for the services of a good stove-maker.
Believe me, the amount is very significant. An additional disadvantage is that the premises where such work is carried out will not be usable for some time.
Option two: reconstruction of the chimney using the lining method.
In simple terms, lining is the insertion of a piece of new pipe into the smoke exhaust ducts. This is permitted by the rules for installing chimneys.
More about sleeve methods
Lining the chimney can also be done using a flexible stainless steel pipe. It is worth noting that this will not be the best option. Such a pipe has its drawbacks: the corrugation will not be an obstacle, but on the contrary will help condensate and soot accumulate + the service life of the structure is reduced due to the small thickness of the walls.
There is another way to “level” the chimney: line the inner surface of the channel with a fire-resistant mixture. Thanks to this, the brick surface of the chimney pipe is smoothed, because the mixture closes all the cracks. In this case, the smoke channel does not decrease significantly in size. If you have a large smoke channel height, you should make a technological hole at the bottom. After the lining work is completed, it must be laid. This will cost you less than lining a chimney; in this case, the price will be much lower. However, it will not provide guarantees of tightness.
It is easier to install the liner when the chimney is being installed, i.e. at the construction stage. This will be both more reliable and save your family budget. Therefore, be sure to take this issue into account during the construction stage. Don't ignore him!
The main thing to remember is that the correct lining of the chimney is, first of all, the safety of your home and the health of your loved ones!
Key mistakes when lining
The main mistakes include:
- Partial liner (not along the full length of the shaft).
- Using a knee instead of a special support element.
- Crumpling of the edges of pipes (if we are talking about stainless steel) during transportation, connection (of segments to each other) or lowering into the shaft.
- Jerks of the cable when lowering the sleeve.
- Narrowing of diameter.
- Too sharp turns (if we are talking about a polymer liner).
- Use of bulk thermal insulation (between the sleeve and the brick shaft).
- The absence of a U-shaped water seal - if the condensate is discharged directly through the hose into the sewer.
Please note: every mistake is quite serious. If you allow them, you can complicate your task in the future (if you need to replace the liner), or worsen the operation of the boiler.
What is a spark arrester, why is it needed on a chimney, and how to make it?
How to clean soot from a chimney using potato peelings?
Related Posts
Installation of a smoke exhaust duct
The simplicity of the chimney design allows, if you have some experience, to calculate and make it yourself. Laying a brick chimney with your own hands will significantly save financial resources.
A short instruction will help you design and build a chimney correctly, as well as line it.
- At the first stage of the work, it is necessary to correctly calculate the main characteristics of the smoke exhaust duct:
- traction force;
- pipe diameter and height.
With the correct diameter, as the height of the chimney increases, air circulation also increases. The basic requirements for how to build a brick chimney, as well as provisions for the choice of material, structure size and installation procedure, are set out in the main regulatory document SNiP 41-01-2003 “Heating, ventilation and air conditioning”.
- Before making a chimney out of brick, it is necessary to provide for its lining at the construction stage;
Installation of smoke exhaust pipes
- Installation of smoke exhaust pipes begins from the heating facility. Each subsequent pipe link is inserted into the previous one. To protect the structure from moisture, it is necessary to use a special heat-resistant sealant;
- All joints are fixed using clamps;
- When laying, it is necessary to completely prevent the pipes from coming into contact with other communications (gas, water, electrical wiring, etc.);
- It is necessary to provide for the installation of a door for cleaning the smoke exhaust duct during its operation;
- If pipes are planned to be located near flammable finishing items, they must be insulated;
Brick chimney laying diagram
- When laying a stainless pipe through the roof, it must be insulated with mineral wool;
Insulating the pipe from the roof elements using mineral wool
When laying bricks, special attention is paid to the evenness of the walls and the accuracy of the corners; During laying, it is necessary to provide technological holes and a place for installing the door to clean the channel from the formed soot; The outer part of the fireplace (stove) chimney can be lined with tiles or decorative bricks;
Photo of how to build a brick chimney, taking into account all the important structural elements
- It is necessary to build the chimney as vertically as possible. The fewer turns and inclined sections, the more efficiently the smoke will be removed from the brick fireplace (stove) to the outside. The length of horizontal sections should not exceed one meter.
Installation of a stainless steel chimney
The parts for assembling a stainless chimney are very diverse, so the channel configuration can be any without harming the draft force and the working process in the stove. Quite often, a corrugated pipe and several elbows become an element of the chimney, helping to avoid a global reconstruction of the walls.
Instructions for assembling the smoke channel
A stainless steel chimney is installed as follows:
- A design sketch is created on paper, which reflects the expected configuration of the smoke channel. Then the walls are marked, indicating exactly where the pipe will be attached. Based on the results of this work, the length of the structure is determined and all parts are found, including rotating elements for connecting pipe sections. At the same time, do not forget about the fragment of the chimney that goes onto the roof of the house. It should rise slightly above the level of the roof ridge.
- Before assembling the chimney, the pipe joints are lubricated with a sealing compound. A special tool will make the articulation of parts more reliable.
- Moving from bottom to top, one chimney section is connected to another. The elements are joined to each other so that the upper section is inserted into the lower section using a special latch. In the absence of this device, one element is inserted into the other by approximately one-half the size of the outer diameter.
- Clamps are attached at all joints of elements. The manufactured structure is fixed on the external or interior wall of the house every 1.5 or 2 meters. Elements passing through the wall and inspection sections of the pipe must be secured. The smoke duct is fixed to additional brackets in the areas where the tees and elbows are located.
Video: connecting chimney elements
Rules for installing stainless pipes
Installation of the structure should be carried out according to the following rules:
- horizontal elements and elbows cannot be installed in places where they will be in close contact with electrical wires and gas pipes;
- chimney elements must not be connected where the structure passes through the wall;
- pipe fragments located horizontally cannot be made long (the permissible limit is 1 m);
- The direction of the chimney can be changed no more than three times;
- the diameter of the selected stainless steel pipe cannot be less than the size of the pipe coming from the furnace of the stove or fireplace;
- when running a smoke duct through the wall, ceiling and roof around an uninsulated stainless steel pipe, it is customary to leave at least a meter of free space;
- the height of the smoke channel must be more than 5 meters, otherwise the products of fuel combustion will be poorly drawn out;
- It is customary to pass a stainless steel pipe through non-flammable roofing material, creating a clearance of 13–15 cm;
- a stainless steel chimney installed outdoors or in a cold building must be covered with thermal insulation materials;
- at the point where the smoke duct exits through a roof made of flammable materials, it is necessary to install a device that extinguishes sparks.
Important principles for installing a chimney
If you want to make your chimney work efficiently, you should listen to some recommendations. In many respects they relate to the use of corrugated pipes. It can be installed both inside and outside the house, but the best place to place such a product is considered to be the transition from the stove pipe to the main channel.
The advice of the experts does not ignore the shape of the hole for the pipe. It is better to make it rectangular or elliptical. The hole in the roof should be located where the smoke duct can pass centrally between the ceiling beams and the roof support structure.
Most often, a rectangular hole is created for the chimney pipe, since it is easier to cut and seal.
Installation of a stainless steel chimney requires mandatory waterproofing of the structure.
This is important, because the upper section of the pipe, not protected from dampness, can cause moisture to leak onto the attic floor
Video: installation of a chimney from a sandwich pipe
58d9d363771891d8798fa0f17f75badd.jpe
The smoke exhaust channel, made of stainless steel pipes, copes well with the functions assigned to it. The installation of this structure will seem simple, like an easy mathematical problem, if you know the intricacies of the process and take into account the advice of the experts.
Sleeving methods and materials
There are several ways to line a brick chimney using various materials and technologies.
Stainless steel pipe
The solution is relevant for smoke mains of any shape and length. Stainless steel sleeves provide excellent resistance to high temperatures and condensation. The structure is easy to install; no special equipment is required. Most often, owners of private houses line the chimney with a pipe with their own hands.
Stainless steel inserts of various designs are available on the market:
- round pipes. Perhaps the most popular liner option. Models are made with a cross section of up to 100 cm. The wall thickness varies between 0.5-1.5 mm, this design parameter depends on the characteristics of the base material,
- rectangular pipes. A stainless steel insert of this category is used less frequently than an analogue with a round cross-section. Models with dimensions of 14x27 cm are relatively common,
- oval pipes. The thickness of the material is 0.5-0.6 mm, common sizes are 20x10 and 24x12 cm. The cross-section of the oval-shaped stainless steel liner of the required sizes corresponds to a round pipe with d15 and d29 cm,
- corrugated stainless steel sleeves. The corrugated pipe is presented in the form of a two-layer model made of different grades of stainless steel with a cross-section of up to 35 cm.
As practice shows, the potential of a corrugated stainless steel liner provides a service life of no more than 4 years, since the ribbed walls become clogged and the liner burns out under the influence of temperature loads.
Polymer sleeve
The liner is made on the basis of fiberglass mesh with polymer impregnation. Models are made up to 60 m long. Thickness parameters vary within 50 cm. The polymer solution provides a long service life - up to 30 years. The material is resistant to condensation.
The chimney can be lined with a polymer sleeveThe convenience of installing a flexible tab lies in the fact that a one-piece hose is inserted into the smoke channel, which can bend at an angle of 30°, which is important when there are bends in the brick main. At the same time, shaped elements are introduced into the design if necessary.
They note that without special equipment and certain skills, it is impossible to install a polymer hose into a smoke shaft yourself. It is noteworthy that models of polymer sleeves for high-temperature and low-temperature heat generators are manufactured using various technologies.
Ceramics
Ceramic liners come in round and oval shapes, the diameter varies from 12 to 45 cm, the length of straight elements is 33, 66 and 133 cm, and the wall thickness is 4-20 mm. Reliable ceramic sleeves are often used in the reconstruction of mines with significant deformations. The material does not react to soot combustion and is valued for its durability. When lining with a ceramic insert, it is necessary to disassemble the smoke shaft. The high cost and impressive weight of the product are the main disadvantages of ceramic sleeves.
Features of installation of liners made of different materials
In modern construction, stainless steel, ceramics or a polymer sleeve are used to reconstruct the chimney. Ceramic liner and polymer are difficult to install. Most often, when lining chimneys with your own hands, stainless steel is used.
Preparatory work
Regardless of the type of liner chosen, a number of preparatory measures are performed before starting liner:
- Using a powerful flashlight, they inspect the smoke shaft from the inside. The degree of destruction, soot contamination, the presence of fallen pieces of mortar, bricks, and bird nests are determined.
- Use metal scrapers, brushes and other devices to clean the chimney. Bricks protruding from the masonry will prevent insertion of the liner. They try to knock down all the protrusions with a hammer or pry bar.
- Measure the length as well as the diameter of the chimney. The dimensions are transferred to the diagram, indicating all rotations and degrees of angles.
- The part of the chimney adjacent to the boiler or stove is dismantled. The installation of the shaped element will begin from this place.
- The bottom of the smoke shaft is cleared of debris and leveled if necessary.
After the preparatory measures have been carried out, the inserts necessary for the sleeve are purchased.
Installation of a stainless steel liner of round, rectangular or oval cross-section
Sleeving a small shaft with stainless steel without turning is carried out according to the following principle:
- All elements of the sleeve are assembled into one structure. The joints are treated with heat-resistant sealant, and the top is wrapped with aluminum-based adhesive tape.
- Two belts, cables or strong rope are secured to the bottom of the pipe with a clamp.
- The sleeve is carefully lowered down the shaft until it touches the bottom. If the length of the chimney is short, a lightweight stainless steel pipe is immersed by hand without using cables.
- The liner from below is connected to the inlet of the boiler or furnace and a condensate collector is installed. The sleeve is removed from the street above the brickwork of the chimney, and a protective cap is put on top.
Stainless steel lining of a long chimney with turns is carried out differently:
- The smoke duct is dismantled at the entrance to the boiler, as well as all areas where shaped connectors will be installed.
- First, the lower part of the sleeve is assembled from flat sections of the pipe up to the first shaped connector. The liner is lowered to the bottom of the shaft, connected to the inlet of the boiler or furnace, and a condensate collector is installed below.
- A shaped connector is installed on the second free end of the steel sleeve. A flat section of stainless steel is connected to it until the next turn of the shaft. The procedure is repeated until the sleeve is removed from the shaft.
The area where the pipes join is similarly reinforced with heat-resistant sealant and wrapped with aluminum tape. A head is installed on top.
Installation of corrugated stainless steel hose
The lining of a flue with a corrugated stainless steel is carried out in a similar way. The difference is the arrangement of the lower and upper exits from the mine. After installing the flexible hose inside the smoke channel, a rigid transition made of stainless pipe is attached from below. This section is used to connect the hose to the inlet of the boiler or furnace. A condensate collector is installed below.
At the upper exit from the smoke channel, the corrugation is placed above the masonry about 30 cm. To securely fasten the head, the exit can be made by extending a rigid section of stainless pipe. Upon completion of the lining, the brickwork of the chimney duct is restored.
Installation of ceramic liner
Lining with ceramic liners is more difficult. The process consists of the following steps:
- A roller mechanism is fixed to the holes of the condensate collector. The element in the sleeve is a load-bearing structure, and the first one descends into the chimney to a depth of 30 cm. Ceramics are heavy. For a safe descent, it is best to use a winch.
- The upper end of the condensate collector is treated with sealant. Using a socket or tongue-and-groove lock, a flat section of the pipe is secured.
- To connect the boiler, a hole is cut out on a flat ceramic sleeve using a universal fitting. A winch is used to lower part of the liner into the shaft. The next element is fixed to the end of the first pipe in a similar way. During descent, make sure that the sleeve with the hole for the fitting does not turn in the other direction relative to the boiler inlet.
When the condensate collector reaches the bottom of the shaft, it is connected to the boiler inlet. From above, a ceramic pipe is installed above the brickwork. The protrusion is made equal to the height of the cover plate.
Installation of a polymer sleeve
To line chimneys with a polymer sleeve, special equipment will be required. Initially, the liner resembles a coiled hose. The hose is lifted to the roof of the building, inserted through a channel to the bottom of the shaft, connected to a compressor and air is supplied. Under pressure, the soft walls of the stocking will straighten out.
When the hose takes on the internal shape of a channel, steam is supplied instead of compressed air. The polymer first softens and then hardens. A condensate collector is installed from below. At the exit from the shaft, the excess piece of the sleeve is cut off, and a head is installed on top.
Head device
To install the head, a rigid sleeve is built onto the surface of the chimney, and a cover plate is mounted around it. A cuff is attached near the pipe to prevent condensation from entering the brick shaft. The part of the sleeve protruding above the roof of the house is insulated with insulation. The height of the pipe should extend beyond the level of the ridge.
Common mistakes
When lining with any type of liner, you must not allow the sections to narrow, use a shaped turn for support, or pour loose insulation into the gaps between the liner and the walls of the shaft.
It is not allowed to drain condensate into the sewer through a hose without installing a U-shaped water seal.
Labor will be useless if the shaft is partially lined, as well as if there are steep angles.
Benefits of rehabilitation
The chimney duct rehabilitation process has undeniable advantages:
- the smooth inner surface of the chimney weakly retains soot;
- the thermal conductivity of the shaft decreases, due to which the pressure difference is maintained;
- the walls of the sleeve made of any material do not absorb condensate;
- a compensator is added to assemble and drain condensate from the channel.
It is always easier to replace a failed liner than to rebuild a brick shaft.
Troubleshooting a brick chimney ↑
While repairing steel chimneys is fairly quick and easy, repairing brick chimneys requires a more serious approach. It can be performed in several ways and largely depends on the reason that caused the problems. When the working element of the heat generator becomes cracked or collapses, the brickwork is repaired.
The main task of the master in this case is to restore the damaged area as efficiently as possible. To do this, it is necessary to disassemble the chimney to the point of damage and re-lay it using new brick. If the chimney design is done correctly, during its repair you will not have to dismantle the entire masonry. If mistakes were made during the installation of the gas and smoke exhaust system, it is easier to completely redo it.
Repair of brick chimneys can be carried out in several ways; the choice of a particular one largely depends on the reasons that caused the problem
When a brick shaft needs to be reworked, the chimney is lined. This repair method will help to avoid labor-intensive and dirty work, which will subsequently lead to the need to repair the roof and the entire room; it is used exclusively when problems arise with a straight chimney, without bends or displacements, and involves the installation of a ceramic or steel pipe of a certain diameter, corresponding to the needs of the heat generator. The result of chimney lining is improved draft, increased tightness of seams and joints, and prevention of soot formation on a smooth surface.
If you need to repair a chimney quickly and efficiently, it is best to resort to lining it. This method does not involve dismantling the masonry. It is based on finishing the chimney duct with special refractory compounds made from granite chips, cement and lime or perlite rocks, characterized by high adhesion to brick and concrete surfaces.
Lining chimneys using Mordax mass
The main features of chimney lining include:
- versatility: this method can be used both for repairing chimneys and ventilation ducts;
- improving draft and simplifying channel cleaning due to the formation of a smooth surface inside the chimney;
- resistance to temperature and atmospheric influences;
- minimal labor costs when performing repair work;
- increased fire safety and minimal risk of leakage of combustion products due to the solidity of the internal surface of the chimney;
- speed of the process (repairing a chimney this way will take a maximum of five hours);
The process of lining the chimney channel begins with preparatory work. It is first of all cleaned of soot, loose pieces and debris, then moistened with a special aqueous solution and a special composition is applied in three layers using a blowing brush wrapped in fabric, which is lowered into the chimney on a winch.
It is important not to forget that each subsequent layer must be applied after the previous one has completely dried.
Chimney lining with polymer liners
Another effective way to repair brick chimneys is to line them with polymer liners. Despite the fact that it has not yet managed to gain particular popularity, experienced craftsmen recommend resorting to it during the work. Lining of polymer liners involves installing special polymer liners developed using new technology into the chimney duct. They not only allow you to quickly restore the chimney, but also minimize the risk of its further destruction.
Repairing a chimney duct using this method is carried out as follows:
- the polymer liner is inflated with compressed air, then steam and mounted in the internal channel of the chimney;
- under the influence of pressure, the liner takes the shape of the chimney channel, fits tightly to the walls and hardens, as a result - a smooth and durable layer of polymer is formed inside the chimney without seams or cracks, resistant to precipitation and high temperatures, soot and condensation do not accumulate on it.
Maintenance of a chimney repaired in this way is quite simple and quick.
Smoke duct lining
Chimney lining or lining is a universal method for reconstructing smoke exhaust and ventilation ducts, which involves the use of special fire-resistant compounds. The most popular means used for the reconstruction of chimney ducts are:
- Mordax;
- Mosan.
The main element that is part of the first product is granite chips. This product is produced in Finland, so it has good quality characteristics. To obtain the necessary solution that will allow you to repair a chimney made of brick, this product is mixed with lime, as well as cement mortar and water. Mosan is a domestic analogue of Mordax, which is made on the basis of perlite.
Both of the above products are distinguished by the fact that they easily adhere to brick and concrete materials. The main advantage of this reconstruction method is that it is done without dismantling the brickwork. After reconstruction, the walls of the internal chimney channel become smooth. Thus, the traction in the system increases and its cleaning is simplified.
As a rule, lining is done very quickly. The entire reconstruction process takes no more than 3–4 hours. Let's consider the order of work during the lining:
- First of all, it is necessary to clean the internal channel of the old brick chimney, removing all soot and other foreign elements from it.
- Next, the canal is moistened.
- At the third stage, a blowing tool (brush) is immersed in the channel, which sprays the composition onto the inner walls of the channel.
- Spraying the mixture is repeated 3 times. Each of the previous layers must dry before applying the next one.
Stage 5. Advantages of chimney rehabilitation (liner)
Lining a chimney with your own hands or with the help of specialists has many positive aspects:
- optimal (even ideal) channel cross-section for gas movement,
- smoothness of the internal surface of the chimney, its minimal roughness,
- non-wetting and non-moisture-absorbing material of the chimney walls,
- low thermal conductivity + minimal cooling of gases over a period of 1 meter of pipe,
- maximum safety in case of insert depressurization,
- high heating rate of the chimney pipe in the cold season,
- protection of brickwork in case of condensation formations,
- possibility of replacing inserts,
- ease of cleaning the channel due to the smoothness of the surface.
Main advantages
A stainless steel chimney has the following advantages over brick and ceramic chimneys:
- a smooth inner surface that prevents the deposition of soot on its walls;
- Possibility of installation in already used premises;
- there is no need to construct foundations for it;
- the presence of sloping areas is allowed;
- the ability to carry out repair work regardless of the time of year;
- due to the insulated design of the chimney, minimal condensation occurs;
- high resistance to aggressive influences of exhaust gases;
- high strength and durability;
- full compliance with all modern fire safety requirements.
Advantages of a steel chimney pipe
Chimney pipes are made of metal, ceramics and brick. Metal pipes are currently in greatest demand. Of all the varieties of this material, it is recommended to choose steel. Steel pipes for chimneys are coated with special solutions that make the material resistant to all adverse effects of the internal environment of the chimney.
When choosing a pipe, it is necessary to take into account the parameters of the heating devices and the fuel used. The material from which the pipes are made must withstand higher temperatures than the fuel can create.
When using some types of heating devices, chemically active substances are found among the under-oxidized combustion products. They can damage a chimney that is not sufficiently resistant to chemicals. Some unburned particles can ignite, creating sparks. Therefore, the material from which the pipe is made must be fireproof.
The advantages of steel pipes are:
- Easy to install. Steel pipes do not require the installation of a special foundation; they do not require complex engineering solutions or special installation tools. You can install them yourself without prior preparation. Due to the plasticity of the material, complex technical structures can be created.
- Light weight. They are easy to transport, you can lift and move them yourself without a team of workers, which also simplifies installation.
- High temperature resistance. Steel products are suitable for appliances operating on any fuel. They do not melt at maximum temperature loads.
- Chemical inertness. Steel does not interact with chemical reagents that can form as under-oxidized combustion products. These substances are not capable of destroying it.
- Corrosion resistance. This advantage applies to pipes that have a special coating and stainless steel. The material itself quickly corrodes. It is worth considering that in addition to the internal environment, the chimney pipe is affected by external unfavorable factors, for example, precipitation. Preference should be given to coated pipes.
- Smooth inner walls. Combustion products settle on the rough surface, turning into soot, which gradually reduces the clearance. This reduces the draft in the chimney. Steel is completely smooth, the risk of soot settling on their surface is minimal.
Features of installing a sandwich pipe on the roof
To bring the sandwich chimney above the roof level, a special link is used, called “roof cutting” by stove makers. Such a structural element should be selected based on the slope of the roof structure. Only taking into account this parameter, all work on the removal of the chimney above the roof will take place without any problems. Doing such work yourself consists of the following steps:
- Using a marker, mark the inside of the roof.
- A hole is installed in the roof structure that matches the diameter and thickness of the sandwich pipe.
- For insulation, a sheet of galvanized metal is fixed to the roof structure, in which
- a hole is cut in advance for the chimney pipe, through which it will come out.
- A groove is mounted on top, on top of which a sandwich pipe is assembled, the length of which must correspond to the calculated parameters.
- At the finishing stage, the edge of the sandwich chimney is protected from precipitation by an umbrella-shaped tip.
As you can see, self-installation of a sandwich chimney is not as simple as it might seem at first glance. But if you familiarize yourself with all the materials and videos, all the work on installing sandwich pipes can be done independently.
However, before deciding on experiments of this kind, you need to sensibly assess all your capabilities, and if you are not confident in them, then it is better to entrust all the work to professionals.
Make it yourself or order it
Tips for choosing
At the beginning of the 20th century, when gas and electric heating were unavailable, stone and brick stoves were widespread. There were many good styling professionals, much more than there are now.
If you decide to order a fireplace or stove and seek the help of a specialist, be sure to pay attention to his professionalism. To do this, it would be a good idea to look at the documents confirming his qualifications and familiarize himself with the portfolio of works.
A poorly constructed chimney is life-threatening. Insufficient draft will lead to the formation of dangerous carbon monoxide, which kills more than one and a half million people every year. In addition, the occurrence of backdraft can lead to fire. Even if a disaster can be avoided, the chimney will still have to be rebuilt, and this is a double expense.
I will provide all the necessary ones below. In addition, you should accurately calculate the dimensions, draw up a drawing, read all the necessary literature and watch a couple of dozen videos on the topic.
The chimney can be of 3 types:
Mounted. Here the oven serves as the base. The minimum thickness of the furnace walls is 2 bricks.
Root. Located on a separate foundation. The smoke outlet pipe of the boiler or stove is connected to the chimney through a connecting transfer hose.
Wall. It is a channel in a load-bearing wall.
Whatever chimney you choose, I personally recommend that when choosing to install it yourself, do not neglect the advice and supervision of a specialist. I repeat - an incorrectly laid chimney will inevitably lead to tragedy.
By the way, for a metal stove you don’t need a brick pipe - an ordinary iron one is enough.
Building regulations
The installation of chimneys for private houses and baths is regulated by the following building codes:
- SP 7.13130.2013 “Fire safety requirements”;
- SNiP 41-01-2003 - “Air conditioning, ventilation, heating”;
- VDPO - “Rules for production work, repair of smoke ducts and furnaces.”
Fire safety requirements for chimneys
The fire safety requirements for chimneys come down to the following main points.
- The wall thickness of the outlet pipe must be at least 120mm;
- Between the inner layer of the roofing pie and the chimney, a fire-prevention retreat must be provided - at least 130 mm;
- When using combustible insulation in the attic floor structure, it is necessary to organize protection in the form of sand backfill;
- The fluff must end at least 70 mm from the upper and lower boundaries of the overlap;
- The distance from the inner surface of the hot chimney to the combustible ceiling structures (fireproof cutting) must be 500 mm or more;
- The walls of the furnace retreat from the combustible structural elements by at least 250 mm;
- The distance between the upper edge of the furnace and the roof slab is 350 mm for intermittently fired furnaces and 1 m for continuous furnaces. This condition applies to a stove made of three rows of bricks. If there are 2 rows, the distances need to be increased by one and a half times;
- You cannot connect two heat sources to one chimney system.
Traction force
The traction force is ensured by the correctly selected pipe cross-section and its height. The cross-section of smoke ducts made of brick is calculated based on the power of the heating device.
The height of the chimney pipe is calculated using special programs and formulas, but there is one rule - the elevation of the chimney above the ridge should be less than 500 mm (if the distance from the chimney to the ridge is less than 3 m).
In a vertical brick chimney, draft is generated by convection.
Therefore, for the normal functioning of the chimney, it is important to take care of its insulation. I’ll tell you how to arrange the insulation a little later.
The right brick - what is it?
The chimney will last a long time, and its walls will not collapse from temperature changes and exposure to precipitation only if the brick necessary for these purposes is selected and used, and the mortar used for masonry must meet a number of requirements.
The brick for the chimney must be solid, fire-resistant and fired. For the construction of a chimney, bricks are selected according to grade, which, in turn, is divided into three grades:
- Grade I has a bright, red color; a yellow tint is acceptable. This type of brick must have a high clay density. There should be no signs of destruction or burrs on the surface of the brick, in particular on the ribs. By tapping such a brick you can hear a ringing sound.
- Grade II has a pale orange color; in addition, it is characterized by low resistance to frost, low density, and high porosity. When you tap it with a hammer, you can hear not a ringing, but a dull thud. There may be burrs and traces of chipping on its flat surfaces and edges.
- Grade III is burnt brick. This material has a deep red color, say, a brown tint. This type of brick is not resistant to frost. This type of brick has a dense but porous structure and has high thermal conductivity. This material has good compressive density, but when exposed to other loads it quickly collapses. Chips and spalling may occur on its surface and edges. When you tap it, you can hear a very ringing sound.
There are two ways to prepare bricks. The first method implies that the brick will be immersed in water for some time. In the second method, the brick is laid in place dry, but at the same time it will begin to absorb moisture from the mortar, which leads to a decrease in the strength characteristics of the masonry as a whole. The mason involved in the construction of the chimney himself chooses the technology for preparing and laying the chimney.
Requirements for the solution
The solution used for the construction of the pipe must ensure the evenness and tightness of the seams. In addition, it must be resistant to the external environment. During the construction of a furnace, there are several zones for which separate mortar compositions are used. There are 11 such zones in total. But compositions according to special recipes are used only in six of them. For example, when laying the first rows of a main chimney, a solution is used, mixed in proportions of 3 to 1 or 4 to 1. At the same time, some craftsmen add lime to increase elasticity. This additive makes it more elastic.
In some sections of the pipe, the air temperature can reach +400 degrees. To reduce the heating of roof structural elements, expanded clay is sometimes added to the solution.
The section of the chimney that faces the street is exposed to temperature fluctuations and precipitation, so its operating conditions can be considered very harsh. In this case, a solution made of sand, clay and cement is used.
When preparing the solution, it is necessary to use only those components that have been pre-cleaned. To filter sand, use a sieve with a mesh size of 1x1 mm. After soaking, the clay is rubbed through the same sieve. This method is considered to be the most effective.
When making a solution, you must follow some rules. In particular, it is necessary to use only pre-soaked and cleaned clay. The soaking process takes 12 - 14 hours, and it must be accompanied by constant stirring. If necessary, add water to it. At the end of this period, sand is added to the clay. The proportions can be 1 to 2, 1 to 3, 1 to 4. This is determined by the fat content of the clay. The higher it is, the more sand needs to be added to it.
Before using the finished solution, it makes sense to form prototypes; they are usually made in the form of balls or strands. After they dry, it will be possible to determine which prepared solution can be used. When laying bricks, the mixture should be applied in a layer 8 -9 mm thick, after the mixture is pressed with the top brick, the thickness of the seam should be 6 - 7 mm.
A properly prepared solution, when raked with a trowel, should hold its shape and not tear
Positive aspects of sleeving
Chimney liners have many advantages:
- proper removal of condensate from the mouth of the smoke exhaust structure into the sewer system or a container specially installed for this purpose is carried out;
- there is free access to cleaning the chimney from soot;
- the tightness of the chimney increases;
- heat loss is reduced;
- the presence of a metal pipe head and a horizontally located protective plate reduces the ingress of moisture onto the inner surface of the brick or stone masonry.
Service price
The cost is calculated individually based on the length of the pipe and the type of material used to make the inner liner. By consulting with our specialists, you can find out how much cladding will cost for your home. You can be sure that it will cost much less than installing a new pipe.
The ideal condition of the smoke exhaust channels is not only a mandatory requirement that must be met for the legal operation of heating equipment. This is a matter of safety for people in the premises. According to statistics, carbon monoxide poisoning occurs quite often during the heating season. This substance has no odor, so people do not notice the problem and quite often end up in the hospital in serious condition. If there are children in the house, then poor draft in the chimney can be fatal.
Specialists from Ventgazservice LLC will restore the patency of smoke channels using special inserts. This will provide good traction and prevent the rapid accumulation of soot. Our priorities are compliance with industry standards and safety.
Where is it sold and how much does it cost?
It is easier to find specialists in the sale and installation of polymer stockings in large cities of the CIS countries. They cannot be found in provincial areas. Therefore, people living in the outback have to overpay. The estimate usually includes payment for the purchase, delivery and installation of Furanflex - the price can ultimately rise significantly.
If we talk about the cost of a polymer hose separately, it depends on the diameter of the product. The price is usually indicated in rubles per 1 linear meter. Approximate prices are given in the table.
Product diameter (mm) | Product cost (rub./linear meter) |
100 | 6550 |
150 | 7750 |
200 | 9200 |
300 | 12300 |
400 | 16600 |
600 | 31000 |
Based on the data in the table, you can make an approximate calculation of the cost of lining a pipe with Furanflex. So, if the length of the chimney is 10 m and its diameter is 200 mm, then a hose will be required that costs at least 92,000 rubles. This amount does not include additional services such as rental of special equipment and professional installation.
Stage 1. Start of sleeve
After all the preparatory work has been carried out, or after dismantling the old chimney (if required), clean the smoke channel and at the same time check its passability. A brush is used for cleaning. If there are sagging mortar on the masonry, knock them down and level the walls. All this is carried out through the top of the chimney or through an additional technological opening.
Then attach a winch to the mouth of the chimney to lower and lift the liner. Distribute the components among the floors and proceed to leveling the bottom of the shaft. At the same time, do not forget to provide a ventilation hole and a condensate drain connection.