Ariston water heater (80 liters): characteristics of the models and their main advantages

The comfort of a modern apartment is impossible without warm water. But utility services are in no hurry to make our lives easier and more enjoyable. Therefore, you need to take care of the comfort in your home yourself. Equipment stores offer us a huge selection of water heaters. Which one should I stop at?

If your home is not suitable for the installation of geysers, then opt for Ariston 80-liter boilers. This is a well-known Italian brand that has become a leader in the development and manufacture of household appliances. In order to dispel your doubts, we will explain the boring instructions in an accessible language.

Advantages of Ariston technology

Like all Ariston equipment, water heaters from this company have many advantages:

  1. The first of them can be called a stylish design that helps to decorate any interior. Moreover, each of the models is created in accordance with the latest technologies.
  2. The Ariston 80 water heater has the longest service life. This effect was achieved due to the fact that the internal walls of the storage tank are covered with a layer of modern material that protects the tank from plaque and rust.
  3. Built-in latest dividers prevent mixing of already heated and cold water. This helps maintain the temperature of the liquid. The Ariston heater is also protected from overheating thanks to built-in temperature control sensors.
  4. The presence of a protective shutdown device that is triggered in moments of sudden voltage changes.
  5. Using Ariston water heaters, users can significantly save on gas or electricity consumption. This is facilitated by the presence of thermal insulation, which keeps the water hot for a long period of time.
  6. Many models of water heaters are equipped with protection against the appearance of bacteria, which makes it possible to use purified water. If there is no water in the system, then you don’t have to worry about the water heater turning on, since it is equipped with special protection.

Blitz tips

A few tips that will allow you to extend the life of the device without overpaying for electricity:

  1. Do not unplug the device. Maintaining a set temperature takes much less energy than heating it up. This is especially true in winter, when the water temperature is especially low.
  2. If hot water is needed less often than once a day, then it is better to turn off the device. In this case, heating will take less energy than maintaining the temperature.
  3. Significant savings are achieved through controllers. The unit can be programmed to heat water at the desired time.
  4. If possible, use the controller mode marked “E” (Eco).
  5. Do not allow water to flow aimlessly. Once again, turning off the tap for a couple of minutes will save you a lot of energy and money.

By following these simple tips, you will not only extend the life of your boiler, but also significantly save on electricity.

Design of ARISTON water heaters for 80 liters

The external simplicity of any water heater carries with it the same uncomplicated internal structure. The difference can only be observed in the external design and materials from which the heater is made. The external structure of the body can be made in a cylindrical or flat shape.

Any water heater has:

  • The internal tank is a boiler into which cold water flows. It is framed by an outer casing.
  • The water that enters the tank is heated by a built-in heating element . To heat water faster, the boiler may have two heating elements.
  • Thermal insulation layer , which is present between the body and the boiler, performs the function of a thermos, which allows you to maintain the water temperature longer.
  • Water enters the tank through a shortened pipe with a divider . The heated water is supplied by the outlet pipe.
  • Magnesium anode built into the Ariston 80 water heater prevents the deposition of mineral salts on the walls of the inside of the tank. This element is replaced as needed.

  • During heating, when the set temperature is reached, the thermostat , which automatically interrupts the power circuit.
  • If the heating element is turned on and the water temperature drops below the set values, then the configured thermal relay .
  • The voltage indicator (indicator light) allows you to control the operation of the water heater
  • The built-in thermometer makes it possible to monitor changes in temperature.

The Ariston 80 storage water heater, which belongs to the flat horizontal models, has the same typical internal structure.

We recommend Polaris instantaneous water heaters: popular models and their characteristics. Reviews

How to turn it on

The design of all boilers (storage water heaters) is the same, so it depends little on the model and brand. Considering that, according to statistics, the most popular manufacturers among Russian consumers are Thermex and Ariston, using their example, we will tell you separately how to turn on the Thermex boiler and how to turn on the Ariston water heater.

The initial installation of equipment is mainly done by specialists, but switching on must be done by the users themselves.

So, how to turn on a Thermex water heater so as not to damage it and prevent mistakes. Connecting an instantaneous water heater is not fundamentally different - the air is also vented, the hot water pipe is shut off, the settings are set and it starts up. The only difference is that the storage one takes 2.5-3 hours to heat the water, and the flow-through one dispenses it after 5-15 seconds.

  1. The shut-off valve on the hot water pipe is closed.

Even if a tap is installed on the pipe, shut-off valves are still used. The taps can let water through, and then the water from the boiler will go into the common riser.

  1. Air is released from the system by opening the hot water tap and the outlet of hot water from the boiler itself; lastly, open the cold water tap. The presence of air can be determined by a ragged stream - it will flow intermittently and a “snorting” sound will be heard.
  2. After the water flow has leveled off, close all the taps, including those on the device itself. Next, connect it to the network.

A separate grounded socket is always used for connection.

  1. Before turning on the boiler, set the temperature and check the operation.

To make sure it works, do the following:

  • check the indicators;
  • check the temperature;
  • If the device is working properly, the temperature will rise after 15-20 minutes.

If the water heater does not turn on

The first thing you do is check the network elements - electricity, sockets, RCDs, automatic devices. Use a tester to check the voltage in the boiler to rule out a broken cable.

The most common problem is electronics. If power is supplied, but the Thermex water heater does not turn on, look at the error code on the display and check the instructions to see what it means.

  • breakdown of the heating element, contamination of the heating element with lime and calcium deposits;
  • thermostat failure - when the water temperature rises above 90-92 degrees, the RCD may be triggered;
  • there is no water in the tank - if there is water in the system, but it does not flow into the boiler, the reason may be that the air has not been bled.

Even if there was water in the tank before turning it on, but it has not been used for a long time, you should first drain the water, and then be sure to drain the air.

Let us repeat that there is no fundamental difference in connecting storage devices, so we will schematically describe how to turn on an Ariston boiler.

  1. If we are talking about an apartment or house with a centralized supply of hot water, close the pipe with shut-off valves.
  2. Open the tap in the place where the unit is installed and drain the water, close it.
  3. You bleed the air from the boiler, for which you first open the inlet tap (the pipe is marked in blue), then the heated water tap (marked in red). Wait until all the air comes out and the water flows in an even stream without interruption.
  4. Do not close the cold water supply tap - its quantity in the boiler is regulated automatically.
  5. Plug it in and set the temperature on the device.
  6. Check the functionality - after a few minutes the temperature in the tank should begin to increase.

What errors can you encounter during operation?

Instantaneous water heaters

As for compact water heating devices, we note that their installation is very simple:

  • remove the old tap;
  • install the unit;
  • connect to a pipe with cold water;
  • turn off the hot one;
  • plug into the outlet.

At this point, the installation is complete and then you just need to turn on the hot water tap and use it. With this equipment, there should be no questions about how to turn on the boiler when it is already installed. If you don’t risk installing it yourself, contact a specialist.

All listed devices belong to high power equipment (from 3 to 7 kW), they are prohibited from being connected to a common outlet. A separate outlet should only be located in a dry place, and power should be supplied directly from the distribution panel.

Shuttle Ariston electric water heater: instructions for using boilers, diagram

After purchasing such an assistant as an Ariston 80-liter water heater for your home, the instructions should be the first document that should be carefully studied before you start using it. This will help you understand all the nuances of working with the boiler and extend the operating life of the device.

An Ariston 80 liter water heater is used to supply the house with hot water. Many positive characteristics contribute to the choice of this series of heaters.

The Ariston 80 v water heater has the same design and instructions for use as all models in this series. Installation should be carried out in accordance with the attached diagrams.

Checking for correct operation

It’s great if the water heater is connected to a separate machine. If problems arise in its operation, this will not affect the power supply to other appliances in the house.

If after starting the heater the circuit breaker is knocked out, you can turn it on again. If the situation repeats itself, then there is a serious problem. The unit must be de-energized and a technician must be called.

Here are a few more details that need to be checked after putting the boiler into operation:

  • Inspect the hot water pipe to see if there is a leak. The fact is that a water heater can create more pressure than in risers. And if the gaskets are already worn out somewhere, but withstood the load from the central water supply, now they can give up.
  • Make sure that the light indicating the supply of voltage to the heating element comes on.
  • Take readings of how many degrees the meter shows at the very beginning of operation of the device, and then look at the temperature again after 20 minutes. If the data has increased, the heating element has successfully survived the rest period and is heating properly.

Connecting the Ariston boiler

It is better if this work is carried out by specialists. The rules to follow when installing the device are given below:

  1. It is necessary to inspect the safety valve, which should not have visible flaws. If they are present, then the damaged part should be replaced.
  2. Plastic dowels are used to screw in screws.
  3. Be sure to check all grounding elements.
  4. An electric heater requires a separate power line to operate. The use of extension cords is strictly prohibited. The socket is placed in a damp place.
  5. In operation, you must use the plug that came with the kit.

The Ariston 80 water heater performs the following functions :

  • On/off. After switching on, the entire system starts up, which is due to the indicators lighting up, and the temperature of the water in the boiler will be displayed. If the indicators are not displayed or flashing, this indicates that the system is disabled.
  • The Ariston abs vls 80 water heater has a power level adjustment function, which makes it possible to set the required parameters.
  • The Ariston abs vls pw 80 water heater allows you to use the antibacterial function, which can be activated or disabled by holding the “power” button for 5 seconds.
  • Possibility of adjusting the temperature using the “+” or “-” buttons in the range from 30° to 75°; The displayed indicators are not recorded. After switching on again, you need to set the values ​​again. Standard temperature values ​​are 75°, power – 1500 W.

Rules for using the device

You can use the storage type device immediately after the first start. To do this, you need to turn it on and select the operating mode. Throughout operation you will have to follow some rules. They will help increase the service life of the boiler.

  • Before turning on, check the presence of water in the tank. This will prevent the heating elements from failing.
  • It is recommended to install a filter on the pipe supplying water to the boiler. It will protect against dirt and reduce water hardness.
  • During the year, descale the drive at least once.
  • Periodically monitor the performance of the protective anode, change if necessary.

Read how to choose pipes for water supply in a private house.

PVC pipes and fittings for water supply are the key to quality water in the house, read about the benefits.

To make the water tastier and healthier, take care of filters for your private home, read about it at https://klimatlab.com/vodosnabzhenie/filtraciya/filtry-dlya-ochistki-vodyv-chastnii-dom.html

Flow-type devices require compliance with several other rules.

  • Check the water pressure before turning on the power. A weak stream will not allow the device to function normally.
  • If the temperature is uncomfortable, adjust it using the buttons on the body or by rotating the mixer tap.
  • If the heater is installed in a bathroom, provide splash protection.
  • Hot water is no longer needed - be sure to turn off the device.

Both devices are not recommended for installation in rooms where temperatures may drop below zero. This will cause the water inside the device to freeze and cause it to break.

Equipment reliability depends not only on product quality. Also important: correct installation, switching on and use of equipment. Compliance with the recommendations given in the article will significantly increase the uninterrupted operation of the boiler.

Rules for operating a water heater

Extending the life of an Ariston brand storage heater is not difficult; you just need to install it according to the instructions and strictly follow the rules for operating the device :

  • The presence of water in the boiler should be checked every time the device is turned on and off. Switching on is possible only when the tank is filled with water.
  • If the power cord is damaged, it must be replaced with material of the same brand, which is best purchased at a specialized retail outlet.
  • If the heater will not be used for a long period, especially in the cold season, then the water from the boiler must be drained, following all the rules prescribed in the instructions. After this, the cold water supply tap is closed. After these steps are completed, the heater is disconnected from the electricity supply.
  • Over time, the heater requires cleaning from dirt. To carry out this work, it is better to use the services of specialists.

We advise Insulation of pipes: protection requirements and choice of materials. Which pipe insulation to choose

Installation

Installing an Ariston water heater with your own hands is not difficult if you carefully read the instructions and follow its instructions. Of course, you can invite specialists who will do everything quickly and efficiently. The only “but” is the price of this service. For example, in Moscow it ranges from $100. Meanwhile, having minimal skills in working with plumbing, you can cope with this task in just 2-3 hours. Considering that you will spend some money on supplies, the net savings will be approximately $60.

Water heater connection diagram.

When assessing the pros and cons of installing a water heater with your own hands, take into account the risk of flooding your neighbors below; if something goes wrong, balance your strengths. The advantages of solving this problem yourself include:

  • saving time and money;
  • acquiring the skills you will need while operating the water heater.

Access to the storage water heater (boiler) must be absolutely free, and the wall for mounting must be strong, capable of supporting double weight (for a unit capacity of 50 liters, calculate the load of 100 kg). Determine the condition of your electrical wiring: is it capable of handling the significant additional load? For example, for a 2000 W water heater the copper wire cross-section should be 2.5 mm². Keep in mind that if there are old water pipes in the apartment, sometimes you have to first replace them and only then connect the boiler. Find out what amperage your electric meter is designed for. If it is less than 40 A, you will have to replace it too.

Reviews of ARISTON water heaters with a volume of 80 liters

For those buyers who took the plunge and purchased an Ariston water heater, the reviews remain purely positive. Below are some of them.

“Advantages: excellent “worker.” Disadvantages: none found.

Since we have a private house and no gas, it was decided to purchase a boiler. I’m tired of constantly heating water on the stove in order to buy food and even just wash the dishes. We asked friends who already had experience working with such units. They, in turn, recommended an Ariston water heater. After reading more reviews, we chose a brand like ARISTON.

We purchased a model with a volume of 80 liters. This is quite enough for a family to use. I really liked the presence of a sensor with which you can always find out the level of water temperature so as not to “get into trouble”)). This heater served us for many years, it was even sad to leave (it was removed because we installed gas and connected a double-circuit boiler). But during its service, this heater proved to be excellent: it quickly “delivered” hot water and maintained its temperature for a long time, consuming little electrical energy. In general, the model is excellent!!!”

“Advantages: compactness, fast heating of water, low electricity consumption, equipped with additional protection. Disadvantages: none.

Excellent water heater. I had to get acquainted with him when the systematic shutdown of hot water in houses began for indefinite periods. In order not to sit and wait for a “miracle,” it was decided to buy a water heater. On the advice of the seller, we purchased a heater

Ariston SG-80, which did not have a high price. And we liked his appearance too. The place for the boiler was determined in the toilet, where it did not cause any inconvenience to anyone. During use, we were convinced that we had taken an excellent assistant: it quickly heats water (80 liters in 4 hours), consumes little - 1.5 kW, heats water to an acceptable temperature - 75o, there is a safety valve and a magnesium anode. We were completely satisfied with the choice!”

“Advantages: simplicity, reliability, ease of use. Disadvantages: I didn’t find any particular ones.

An Ariston SG-80 brand water heater came into our home back in 2013, we bought it at a discount and did not regret it. My husband did the installation himself, and it turned out to be not that difficult. The heater serves the bathroom and sink. There is plenty of water, despite the fact that we set the heating level to 50o, this allows us to save a little. It takes an average of 2 hours to heat 80 liters at this temperature. I was very pleased with the quiet operation of this device. We were pleased with the purchase."

“Advantages: heating up to 75o, low energy consumption. Disadvantages: little significant, but the lid is poorly thought out.

Our small town is not connected to hot water supply. While we lived together, we got by. But after the baby was born, we decided to buy a boiler. We chose 80 liter models available at our expense. We settled on the Ariston SG 80 model, which suited us in all respects: energy consumption of 1.5 kW, volume, heating temperature, which reaches 75° and, of course, price.

Having installed it, we ourselves felt the advantages. Everything worked like a charm. It was a little inconvenient when switching the temperature when it was necessary to switch the lever under the lid. It was not entirely convenient to get a screwdriver to the right place. But this is not so significant, because we only had to change the temperature indicators once. Overall, the model is excellent. I recommend to all!"

We advise How to take meter readings: what are the values ​​​​on the meter and how to pay the water bill?

Models and displacement

Due to the popularity of the product, the manufacturer produces a large number of models with different characteristics. Models with electric heating elements differ in volume and the presence of a storage tank, power, and water temperature limit. The higher the power of the heating element, the higher the maximum heating temperature.

The list below shows the most popular Ariston brand water heater models on the market and its brief characteristics:

  1. ABS VLS (VELIS) ​​EVO PW 50 – electric storage water heater. Volume - 50 l, equipped with a fast heating function, an electronic thermometer for monitoring the water temperature, and a safety device to prevent it from being turned on if the storage tank is empty.
  2. NTS 80V 1.5K SU 3700366 – electric storage water heater. Volume - 80 l. Equipped with an external temperature regulator in the form of a round scale.
  3. ABS VLS EVO INOX PW 80 D - electric storage water heater. Volume - 80 l. The tank consists of 2 40-liter compartments. Has the ability to accelerate heating, there are 2 heating elements.
  4. ABS PRO R 100 V - electric storage water heater. Volume - 100 l. The model is equipped with overheating protection (ABS safety system). Energy savings are ensured by polyurethane foam thermal insulation. Vertical installation is provided.
  5. ABS ANDRIS LUX 30 - electric storage water heater. Volume - 30 l. The model has a bottom connection for water pipes. The tank is made of steel, the internal coating is Ag.

Components for electric storage water heater Ariston.

Ariston electric storage water heater consists of:

  • outer body;
  • bracket;
  • internal tank;
  • hot water outlet;
  • magnesium anode;
  • cold water inlet;
  • heat insulator;
  • thermostat sleeves;
  • heating element (heater);
  • flange;
  • thermostat;
  • power cable;
  • regulator knobs.

Today you can find several popular devices on sale. These include the Superlux, Marco Polo and Fast Evo lines. The most discussed heaters are:

Fast Evo, which can have a power of 19 or 24 kW. The rate of water heating depends on this, which can range from 11 to 14 liters per minute. This model is automatic and has the option of electric ignition using two batteries. To keep the tap water temperature at the same level, the model is equipped with a flame modulation system. The control unit contains a manual temperature switch. The front panel is equipped with a digital screen on which you can monitor all configured parameters. If the setting is incorrect, the display shows an error code and the user can make the required adjustments.

  • Marco Polo Gi7S is a turbocharged water heater that does not have a chimney in its design. To connect this speaker, you will need to lead the exhaust pipe to the street. This can be done through a hole in the wall of the house or through a window.
  • "Marco Polo Gi7S 11L FFI" has a closed combustion chamber. This heater has an increased power of 22 kW. The design is modern, the device body is made of metal. The panel has a display with which control is carried out. Ignition occurs automatically.

Important! The operating instructions for Marco Polo Gi7S indicate that its installation can only be carried out with permission from gas control representatives.

The type of geyser "Ariston", its design and power level are chosen based on the planned operating conditions. All models are varied and must be selected individually.

Inclusion

If you turn on the boiler for the first time, you should do the following:

  • We inspect the inlet pipes to the water heater and find a check valve. If the normal pressure is exceeded, water will flow out of it. Therefore, you should either place a small container under it, or connect and drain the tube into the sewer.
  • We fill the tank. Open the valves at the water inlet and outlet of the device. To do this, turn the tap handle 90 degrees counterclockwise. Open the hot water tap. We wait until the container is filled. If water starts flowing, this means that the Ariston boiler is full.

It is advisable to visually inspect the pipes for leaks. If water is dripping somewhere, you need to turn off the water and call specialists to fix the problem.

We turn on the device to the network. To do this, we either insert the plug into the socket, or turn on the machine to which the electrical cable is connected. The machine may be located near the installation site or in the distribution panel. We set the desired water temperature. It is recommended to set the level to 60-65 degrees. At higher temperatures, scale actively accumulates, and at lower temperatures, harmful bacteria can begin to multiply.

The temperature can be set with a mechanical knob, as in the Ariston SG 30 OR model, or by buttons on the control panel, as in the Ariston VELIS EVO PW model.

After this, all you have to do is wait until the liquid warms up and start using hot water. For convenience, you can mix cold water from the tap with warm water from the boiler to achieve the desired temperature.

Water dripping

If water drips from the water heater, the reason may be the absence of a safety valve, the installation of a valve with inappropriate parameters, or its clogging with deposits. In this case, excess pressure, which appears as a result of rising temperature and lack of release, acts on the walls of the tank.

Over time, this situation leads to damage to the integrity of the welds and leakage of the tank. Do-it-yourself tank repair is impractical; if the tank is made of stainless steel, argon welding is required, performed only by specialists; if the tank is covered with glass enamel, welding is impossible.

Replacing the tank will result in damage to the housing. If the tank leaks, the water heater will have to be replaced. To avoid this, monitor the serviceability of the safety valve and clean it in a timely manner.


Water leaks cause the body to rust

In operating condition, when heating, water should drip from it, but if water drips even when the unit is turned off, it should be calibrated or replaced with a new one. When purchasing a new one, be sure to choose a valve with the same parameters as the standard one. Calibration can only be performed by service center specialists.

To determine the nature of the malfunction and eliminate it, it is advisable to have an understanding of the structure of the boiler. Below is a diagram of the device with horizontal and vertical installation types.

Main selection criteria

  1. Thermal insulation material.
  2. Control method.
  3. What material is the tank made of?
  4. Power consumption.
  5. Duration and method of operation.
  6. Availability of a protective system.
  7. Quantity and quality of heating elements.
  8. Water heating time and its maximum temperature.

The cost of a water heater depends on the following factors: manufacturer, tank volume, materials of manufacture, power, warranty, additional functions. Prices for electric boilers range from 5,000 to 10,000 rubles. As for gas water heaters, their cost ranges from 13,100 to 23,500 rubles.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]